Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 338Raptor

Pages: [1] 2 3 ... 12
1
FE Technical Forum / Re: High Riser intake manifold question
« on: June 24, 2026, 04:02:04 PM »
I believe the part number I'm looking for is a Dove Part # DOVE-9424-B

2
Private Classifieds / Re: WTB: 427 high riser tunnel wedge intake manifold
« on: June 23, 2026, 09:59:52 PM »
E-mail sent.

I’ll call tomorrow as well.

3
Private Classifieds / Re: WTB: 427 high riser tunnel wedge intake manifold
« on: June 23, 2026, 02:44:59 PM »
2nd try

4
Private Classifieds / Re: WTB: 427 high riser tunnel wedge intake manifold
« on: June 23, 2026, 02:42:58 PM »
This is the one I'm looking for.

5
Private Classifieds / Re: WTB: 427 high riser tunnel wedge intake manifold
« on: June 20, 2026, 01:33:54 AM »
I certainly don’t need 500cfm, 350-375cfm would be sufficient for my needs (496ci).  However, if the tunnel wedges are impossible to find my second choice (2x4 “F”) might be a more practical option anyway. 
But I’m going to keep looking up to the point I need to make a final decision. 

6
FE Technical Forum / Re: High Riser intake manifold question
« on: June 19, 2026, 09:40:24 AM »
I need it to fit under a teardrop hood. 

Based on what I know now...

1st choice - Dove Tunnel Wedge (stock high riser port location)
2nd choice - Factory 2x4 "F"
3rd choice - Pond 2x4 "F"

7
Private Classifieds / WTB: 427 high riser tunnel wedge intake manifold
« on: June 18, 2026, 10:39:51 PM »
Wanted:  Dove Tunnel Wedge intake to fit stock C4AE-6090-F High Riser Heads.

8
FE Technical Forum / Re: High Riser intake manifold question
« on: June 18, 2026, 02:56:32 PM »
That’s what I’m looking for. 

9
FE Technical Forum / Re: High Riser intake manifold question
« on: June 17, 2026, 09:58:00 PM »
If you change your mind I’m interested.

10
FE Technical Forum / Re: High Riser intake manifold question
« on: June 17, 2026, 11:31:28 AM »
John67427: does it fit the stock C4AE-6090-F high riser port locations?  If so, are you interested is selling your Dove Tunnel Wedge?   

11
FE Technical Forum / Re: High Riser intake manifold question
« on: June 17, 2026, 12:42:52 AM »
428KIDD: Is the XE better than the F?  Have you heard?

12
FE Technical Forum / Re: High Riser intake manifold question
« on: June 15, 2026, 10:00:12 PM »
I looked at a D today. I was told it has sufficient spacing to use carbs with metering blocks and it had an angled mount.

13
FE Technical Forum / High Riser intake manifold question
« on: June 14, 2026, 01:33:17 AM »
Can someone educate me about the differences between the different OE High Riser intakes Ford made in the 60’s? 
I listed the ones I know of but I’m sure I’ve missed a few.

C4AE-9425-E   1x4
C4AE-9425-G  1x4
C4AE-9425-D   2x4 dual plane
C4AE-9425-F   2x4 dual plane

Was there a 2x4 tunnel wedge version?

14
FE Technical Forum / Re: Electric prelube pump
« on: September 30, 2025, 08:49:44 AM »
I have one on my Cobra with the Aviaid pan.  It works great. Whenever I start the car after storage or even for the day, I flip the switch and the motor is preluded in like 10 seconds. Simple and effective.
Check out these pumps, Infinity Aerospace GP301-12L or maybe Reverso Pumps

15
Private Classifieds / WTB - 427SOHC OEM rocker arm parts
« on: November 10, 2023, 10:24:51 PM »
WTB Cammer rocker arm wheel shafts and needle bearings. 

Pages: [1] 2 3 ... 12