Author Topic: Gaskets  (Read 2348 times)

0 Members and 1 Guest are viewing this topic.

mike7570

  • Guest
Gaskets
« on: April 27, 2022, 01:48:59 PM »
I was mocking up my engine and I was test fit some header tubes then I realized this is the first aluminum head engine I have put together.
What do you guys use for exhaust (header) gaskets?  Any type better than others?

fryedaddy

  • Hero Member
  • *****
  • Posts: 1249
    • View Profile
Re: Gaskets
« Reply #1 on: April 27, 2022, 02:35:46 PM »
remflex is the best ones i know of
1966 comet caliente 428 4 speed owned since 1983                                                 1973 f250 ranger xlt 360 4 speed papaw bought new

RustyCrankshaft

  • Sr. Member
  • ****
  • Posts: 489
    • View Profile
Re: Gaskets
« Reply #2 on: April 28, 2022, 06:49:56 PM »
Another vote for Remflex. I've had really good luck with them. They aren't the only good header gaskets, but they're a solid choice and very forgiving.

Ranch

  • Full Member
  • ***
  • Posts: 125
  • Retired Maintenance Machinist, Millwright
    • View Profile
Re: Gaskets
« Reply #3 on: April 28, 2022, 07:48:24 PM »
Yep Remflex (RFL3008) should seal about anything.  Thick, soft, but the are a little fragile. I cut mine in a few spots and mount them individually with the flange.   I also use Remflex (RFL-8003) where my collector bolts up to my exhaust (3 1/2" collector)

mike7570

  • Guest
Re: Gaskets
« Reply #4 on: April 28, 2022, 11:56:55 PM »
Thick is not good, very little room with mustang shock tower. What about no gasket?

Lg57

  • Newbie
  • *
  • Posts: 16
    • View Profile
Re: Gaskets
« Reply #5 on: April 29, 2022, 06:28:27 AM »
When using no gasket, I use the high temp orange silicone sealer. Works very well for me. Sorry, I can't recall the brand name,

e philpott

  • Hero Member
  • *****
  • Posts: 920
    • View Profile
Re: Gaskets
« Reply #6 on: April 29, 2022, 07:24:15 AM »
I like the solid copper gaskets myself

SSdynosaur

  • Full Member
  • ***
  • Posts: 135
    • View Profile
Re: Gaskets
« Reply #7 on: April 29, 2022, 10:07:51 AM »
Mike, very nice project. I am an NHRA/NMCA FE racer utilizing aluminum heads in SuperStock. I do not use any gaskets or sealer, but, my headers have only the vertical bolt pattern and were constructed with .250 thick flanges with flatness checked after welding. This was/is my first attempt at running headers without gaskets and I can say that I have been pleasantly surprised at the quality of sealing after using this process for the past 10 years; previously I always used the Mr.G "super" exhaust gaskets, separated into 8 individual pieces. I also use the ARP SS 3/8x1, 12pt. 5/16" wrench-head bolts but on an FE it takes about 10 different 5/16" wrench configurations to complete the job. Good luck, looking forward to your first race.

mike7570

  • Guest
Re: Gaskets
« Reply #8 on: April 29, 2022, 10:38:16 AM »
Thanks for the info, I think I will try no gaskets with a little high temp sealer, I need all the room I can get.  My headers have thick separated flanges and I checked them for flatness before ceramic coat. I have installed FE headers in shock tower mustangs at least 6 or 7 times. I had the process down to 1 socket, 2 extensions and 2 combination wrenches. On my first Mustang I put in all 28 header bolts losing a lot skin in the process, now I will probably use just top and bottom.
Thanks, Mike

cjshaker

  • Hero Member
  • *****
  • Posts: 4448
    • View Profile
Re: Gaskets
« Reply #9 on: April 29, 2022, 01:41:25 PM »
Mike, very nice project. I am an NHRA/NMCA FE racer utilizing aluminum heads in SuperStock. I do not use any gaskets or sealer, but, my headers have only the vertical bolt pattern and were constructed with .250 thick flanges with flatness checked after welding.

I'm curious if the headers you use have the sealing bead around the port, or are they flat? The sealing bead seems like they would tend to warp the sealing surface when the "ears" are tightened down, at least when using no gasket. Just guessing at that though.
Doug Smith


'69 R-code Mach 1, 427 MR, 2x4, Jerico, 4.30 Locker
'70 F-350 390
'55 Ford Customline 2dr
'37 Ford Coupe

shady

  • Hero Member
  • *****
  • Posts: 1001
    • View Profile
Re: Gaskets
« Reply #10 on: April 29, 2022, 03:54:07 PM »
Sanderson says not to use gaskets. Run a bead of hi temp silicon around each tube and let it harden over night, then install. I used permatex copper and it is still working.
What goes fast doesn't go fast long'
What goes fast takes your money with it.
So I'm slow & broke, what went wrong?
2021 FERR cool FE Winner
2022 FERR cool FE Winner
2023 FERR cool FE Winner

mike7570

  • Guest
Re: Gaskets
« Reply #11 on: April 29, 2022, 04:45:51 PM »
Mike, very nice project. I am an NHRA/NMCA FE racer utilizing aluminum heads in SuperStock. I do not use any gaskets or sealer, but, my headers have only the vertical bolt pattern and were constructed with .250 thick flanges with flatness checked after welding.

I'm curious if the headers you use have the sealing bead around the port, or are they flat? The sealing bead seems like they would tend to warp the sealing surface when the "ears" are tightened down, at least when using no gasket. Just guessing at that though.

No bead, they are flat.

Falcon67

  • Hero Member
  • *****
  • Posts: 2151
    • View Profile
    • Kelly's Hot Rod Page
Re: Gaskets
« Reply #12 on: April 29, 2022, 05:23:05 PM »
I use Felpro metal sandwich type header gaskets.  Haven't had any issues with those.  Granted, on the dragster they get applied with some high heat red RTV in places, but they work fine.  Not as critical or long term installation as maybe a street car.  But same have been on the Falcon 351C for several years.

Rory428

  • Hero Member
  • *****
  • Posts: 998
    • View Profile
Re: Gaskets
« Reply #13 on: April 29, 2022, 06:17:34 PM »
I also like the FelPro header gaskets, using them both on my aluminum headed 347 SBF, and my iron headed 427 and 428 drag engines. On my FPA headers, on the 428 in my 59, I used the supplied FPA gaskets, I am going to use the FelPro header gaskets now with the new TFS heads. To me, unless you have headers that you can install with the engine on the engine stand, using silicone on the flanges of the headers , with the engine installed, seems like a great way to just smear RTV all over the heads, header pipes, shock towers, and your hands. And unless both the head surfaces and the exhaust flanges are really straight, I can`t see the RTV being able to seal any voids with high temperature, high pressure exhaust gases.
1978 Fairmont,FE 427 with 428 crank, 4 speed Jerico best of 9.972@132.54MPH 1.29 60 foot
1985 Mustang HB 331 SB Ford, 4 speed Jerico, best of 10.29@128 MPH 1.40 60 foot.
1974 F350 race car hauler 390 NP435 4 speed
1959 Ford Meteor 2 dr sedan. 428 Cobra Jet, 4 speed Toploader. 12.54@ 108 MPH

SSdynosaur

  • Full Member
  • ***
  • Posts: 135
    • View Profile
Re: Gaskets
« Reply #14 on: April 29, 2022, 08:20:12 PM »

I'm curious if the headers you use have the sealing bead around the port, or are they flat? The sealing bead seems like they would tend to warp the sealing surface when the "ears" are tightened down, at least when using no gasket. Just guessing at that though.
[/quote]

My flanges were water jet from .250 thick material and TIG welded completely on the inside and gap welded on the outside with a surface mill for final. Please understand that these headers are competition only and from inception they were intended to mount directly to the head. I would not suggest this method for the street in any way.