1
Non-FE Discussion Forum / Re: SBF. Tunnelwedge Intakes
« on: September 14, 2026, 06:04:53 PM »
I have. I suggested to him to consider taking over castings for Jays parts
Dedicated to Building and Racing the Ford FE Engine
News:
SMF - Just Installed!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
FE Technical Forum / Re: Total Control Products FE engine mounts
« on: August 19, 2026, 07:46:57 AM »
I put a set on 68.5 mustang. Allowed a little more movement. I think they transfer engine vibration more than stock mounts though.
3
Non-FE Discussion Forum / Re: Electric A/C
« on: May 27, 2026, 07:21:14 AM »
I just installed electric ac in 70 mustang. Have not tested it yet . I tend to research items after I spend my money. This is another example of that. Price was good, but it’s all custom install as in making and crimping lines and fabricating brackets. A guy on you tube put one in a Monte Carlo. The cooling results were not great. I now wish I would have spent the money on an after market belt driven kit.
4
Member Projects / Re: '62 Galaxie Progress Report
« on: December 08, 2025, 08:46:16 AM »
Will you be using your new heads on this build ?
5
Private Classifieds / Re: Billet steel cross bolt main caps
« on: October 31, 2025, 04:08:47 PM »
Look great Cody.
6
FE Engine Dyno Results / Re: Lykins Motorsports 482FE w/ FE Power Tunnel Port Heads 586 hp @ 6000
« on: October 18, 2025, 05:16:34 PM »
Good to see more F E products enter the market. Just curious. Would power level be similar with stock trick flow heads on this build?
7
Vendor Classifieds / Re: Best damn FE headers i have ever seen
« on: July 02, 2025, 04:21:51 PM »
One highly skilled individual that built those. I spent my career as a welder/ fabricator and could never match this man’s talent.
8
FE Technical Forum / Re: Survival heads
« on: December 12, 2024, 04:27:40 PM »
I think he recently posted that he’s sold out and wasn’t planning to be restocking soon.
9
FE Technical Forum / Re: My FE engine projects
« on: December 03, 2024, 04:32:23 PM »
Unscrupulous on sellers part, to not mention anything about the hole in block and sub standard repair.
10
Non-FE Discussion Forum / Re: Tom Posthuma - Farewell to a great FE guy
« on: November 04, 2024, 07:46:35 PM »
I always enjoyed reading his posts, very entertaining guy obviously. Sad to hear he’s gone.
11
FE Technical Forum / Re: Toploader hydraulic throwout bearing
« on: September 07, 2024, 03:40:09 PM »
I purchased a McLeod unit from modern drive line . After fighting it for a year and pulling trans several times I spoke to modern driveline. Bruce said. Ya we had a lot of problems with those and no longer sell them. If you don’t like it talk to McLeod. They were equally helpful. Ended up giving it away and going external . Unless they have improved. I would not recommend McLeod.
12
FE Technical Forum / Re: Thermostat
« on: July 11, 2024, 06:30:19 PM »
As usual. Spot on real world input from Rory. I’ve followed his comments on here for awhile and find his input to be of great value .
13
Non-FE Discussion Forum / Re: Happy Birthday to a true legend...
« on: January 27, 2021, 08:20:38 PM »
Had George and his son build a boss 302 strokerfor me a few years a go. Went to his home/shop and picked it up after Columbus swap meet. Was a real treat to meet and visit with them. And the engine has performed very well
14
FE Technical Forum / Re: Engine cuts out when warm
« on: September 07, 2020, 09:27:48 AM »
Update..Looks like Jay and a couple others may have identified the problem..It appears the gas in bowls was overheating. I upped octane. Made a heat shield and installed under carb. Insulated fuel line. Reinstalled distributor with pertronix. Reinstalled factory 735 Holley. Set timing at 12 degree. Running fine now. Thx to all who offered advice.
15
FE Technical Forum / Re: Engine cuts out when warm
« on: September 01, 2020, 02:22:02 PM »
ok Thx Will up the octane