Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - calcoral

Pages: [1]
1
FE Technical Forum / distributor gear removal tool
« on: June 16, 2026, 01:52:58 PM »
does anyone have a thexton #415 tool for sale or know of one thats for sale  ? thanks lee

2
FE Technical Forum / fuel bowl stripped threads
« on: November 11, 2024, 09:27:51 PM »
anyone fixed needle and seat threads on a holley center hung bowl ?  also has anyone tapped the fuel inlet thread on a center hung holley bowl ...trying to repair  and or make a cobra jet primary bowls

3
FE Technical Forum / Re: Fairlane header options
« on: October 25, 2024, 06:10:07 PM »
you might have a clearance problem with the borgeson steering box and lines.maybe someone on hear can tell you...just a thought

4
FE Technical Forum / Re: “Autolite” AGM battery
« on: January 28, 2024, 06:36:01 PM »
i run an autolite agm in my mach 1...445 stroker and stock reman starter no problems so far been in there bout 7 years.that said i had slow laboured hot start .that me a while to figure out but it turned out to be the reproduction battery cables just couldnt move enough juice when hot.i put 1/0 cables in and no more problems.i dont think they have the highest cca but if your electrical sys is in good condition it should be ok...lee

5
FE Technical Forum / Re: FORD RACING FLYWHEEL update
« on: August 17, 2022, 09:12:05 AM »
my main concern was that the rivets would have gouged the flywheel surface too deep to machine.but after removal i see they did not. but after seeing the heat discoloration on the back of the flywheel i will be ordering a new one and new arp bolts. thanks for the reply s and sorry for not explaining my concerns correctly. also sorry for any friction this may have caused...lee         

6
FE Technical Forum / FORD RACING FLYWHEEL
« on: August 15, 2022, 02:36:24 PM »
who made the ford racing flywheel for a fe i cant remember? and does anyone know how much can be removed safely and still be useable? i am pretty sure it will be scarred up after shredding my clutch but i havent got it out yet...thanks lee

7
FE Technical Forum / Oil Separator
« on: March 13, 2021, 01:42:18 PM »
Anyone running a oil separator on a FE street car? Are they worth running? Any brands you recommend? I was thinking they might keep it running a little cleaner what are your thoughts...lee

8
FE Technical Forum / bullet shaped wire terminals
« on: April 28, 2020, 01:53:06 PM »
Does anyone make the origial style bullet connecters  that ford originally used.i have tried several aftermarket ons but they are not the correct size. Just thought with the number of people restoring fords someone would have repoped them....thanks lee

9
Private Classifieds / wtb 428 cj block
« on: November 11, 2015, 04:44:58 PM »
wtb 428 cj block std bore  9g or 9f datecode ....can pick up in columbus at the swap

10
FE Technical Forum / Re: intake dimentions
« on: July 20, 2015, 09:09:31 PM »
thanks for the great responces . its nice not to get smart ass suggestions like on other forums. i am looking forward to listening here on the sidelines and gaining  more fe knowlege and thanks again for the help ...lee

11
FE Technical Forum / intake dimentions
« on: July 19, 2015, 09:37:09 PM »
i have been waiting for edelbrock to come out with a air gap single 4barrel intake but no luck . i am running a fe in a 70 mach 1 with a shaker scoop so the height has to be similar to a cj or pi intake also carb location is an issue also.the dual quad air gap edee is close to the right height and i have looked at the single plane edee but dont think it can be milled enough for clearance let alone how it would work after. can anyone including jay b tell me if one of his adapters with a cleveland air gap intake be anywhere close to what i need or could it be machined to get close ...thanks lee

Pages: [1]