Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - galaxastang

Pages: [1] 2 3 4
1
  That sounds like a plan, thx Woody!

2
  Well...I've since calmed down a little and truly hoping it's a intake gasket. I always run 50/50 coolant, so it freezing doesn't make a lot of sense. Especially seeing that there weren't any issues with my Galaxie, parked in front of my truck, fired right up and ran no problems.
   So I'm going to investigate over the weekend, drain the pan, pull the intake and inspect the gaskets. In a perfect world, I replace the gaskets, oil filter and oil then fire it up after I prime the oil pump.
   Probably shouldn't have, but I left all the plugs out sprayed a little 2+2 in the cylinders to help evaporate moisture.
   Questions - Should I squirt a little oil in each cylinder and crank it over before replacing the plugs and trying to start it or yank the heads too and clean up the cylinders? Still not thinking straight
           Best gaskets (fel pro?) for intake and sealer for china wall?

        Thx guys



3
FE Technical Forum / I think I killed my 390 with neglect, advice needed
« on: October 13, 2026, 04:51:11 PM »
Hey guys,
    Haven't been around for a long while dealing with health issues for a few yrs, my F100 is stored in a insulated garage, but is not climate controlled. I recently went to start it and it cranked and quickly locked up. I couldn't even turn it over with breaker bar and pipe, oh shit moment! So I started to remove 5,6,7, and 8 plugs, still wouldn't turn over, 2nd oh shit moment! Moved to removing 1,2,3 and 4 plugs and splash, first turn of the breaker bar I get coolant shooting out of mostly number 4 cyl. with mist out of 1,2,and 3. Couldn't believe what I was finding, but have no one to blame but myself! Radiator empty, but no coolant on the floor, maybe it's in the pan!? Have not drained the pan or even touched the truck since finding this, I'm sick to my stomach and again have no one to blame but numero uno! Can't be freeze plug with coolant in the cylinders, so I'm hoping head gasket and not the block! My next move is to drain the pan, from there I'm most likely going to have to pull it and inspect block and heads. So...after beating myself up for the last few days, I need to try something before I go in for neck surgery on the 27th. Any advice or ideas are greatly appreciated for stroked 390 to 445 SCAT crank and rods, edelbrock heads and intake.
         Thx in advance, Wally 
   
 p.s.  my 67 Galaxy stock 390, fired up and runs fine

4
Private Classifieds / Re: WTB; Running 390
« on: November 01, 2019, 09:42:30 PM »

5
Private Classifieds / Re: WTB; Running 390
« on: November 01, 2019, 09:27:49 PM »
Hi,
    Might have what your looking for, email me, I'll send pics.  Thx

6
Vendor Classifieds / Re: Comp 839-16 Solid Roller Lifters
« on: November 14, 2018, 10:03:18 PM »
sent you a pm

7
Private Classifieds / Re: 427 medium riser engine
« on: April 13, 2018, 10:51:42 PM »
Any chance you would separate the block from this package? Thx

8
Private Classifieds / Re: 427 medium riser engine
« on: April 12, 2018, 08:36:39 PM »
Any bare blocks going to FE reunion? If so, condition and price? Thx

9
Want are you working on? Think I have some 68 Gal stuff, might be for disc, I think the only difference is a valve in the distribution block or master cylinder. I'll check let me know.

10
FE Technical Forum / Any one traveling from west coast to east coast
« on: March 29, 2018, 09:08:48 PM »
Need a block picked up in southern California going to N.J. let me know.
Thanks

11
Vendor Classifieds / Re: engine shipping cost
« on: January 30, 2018, 03:54:32 PM »
best I found, thanks guys

12
Vendor Classifieds / engine shipping cost
« on: January 29, 2018, 04:34:00 PM »
What is good price Fl to NJ . Fastenal quoted me $235 Thanks

13
Private Classifieds / crank, rods , and piston worth
« on: December 30, 2017, 11:26:50 PM »
Hey guys I have $teel crank, lemans cap screw rods and TRW forged pistons std bore. Have a local guy interested what be fair asking price? Thanks

14
FE Technical Forum / Re: Trickflow is offering cylinder heads!!!
« on: November 11, 2016, 02:03:07 PM »
Talked to TFS rep today, production wont start until summer.
Heads $2000-2200 assembled
Intake $400-450
Those are estimated #'s

175 intake runner
2.19 in - 1.625 ex
70cc chamber

15
Private Classifieds / Re: 428 for sale
« on: July 24, 2016, 09:17:37 AM »
Interested, sent you a pm


Pages: [1] 2 3 4