871
FE Technical Forum / Re: '26 T at AutoRama Houston
« on: November 26, 2018, 12:17:59 PM »
Factory manifolds don't route the tubes anything like those. Not modified 426 Hemi ones either.
Dedicated to Building and Racing the Ford FE Engine
News:
SMF - Just Installed!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
872
FE Technical Forum / Re: '26 T at AutoRama Houston
« on: November 25, 2018, 10:14:47 PM »
Those aren't factory manifolds, they appear to be custom cast like the ones on the Ardun at the SEMA show.
873
FE Technical Forum / Re: Heigth of the HR rocker shafts question
« on: November 25, 2018, 09:38:17 PM »
Hmmm, you have all the pieces in the pictures (which I only looked at now!)
As far as I know he never made a High Riser set since there isn't room under the rockers to run something over the pedestals.
As far as I know he never made a High Riser set since there isn't room under the rockers to run something over the pedestals.
874
FE Technical Forum / Re: Heigth of the HR rocker shafts question
« on: November 25, 2018, 09:35:29 PM »
There was a steel plate that went under the stands and that is what the narrow steel upright end stands bolted to. Sounds like you have an incomplete setup.
Contact Ken at Oregon Cams. He will have those parts.
Contact Ken at Oregon Cams. He will have those parts.
875
FE Technical Forum / Re: Pent Roof Valve Cover ID
« on: November 24, 2018, 07:17:03 PM »
I am surprised some of you don't know 
66 390 GT only, the early 67 used the same left side but had a unique right side made from a 361-391FT valve cover with a tab remove and chromed.
But if we are speculating... wasn't there a chrome dress up package for the 7 Litre that used these valve covers, a chromed master cylinder cap and rad cap?
66 390 GT only, the early 67 used the same left side but had a unique right side made from a 361-391FT valve cover with a tab remove and chromed.
But if we are speculating... wasn't there a chrome dress up package for the 7 Litre that used these valve covers, a chromed master cylinder cap and rad cap?
876
FE Technical Forum / Re: '26 T at AutoRama Houston
« on: November 24, 2018, 07:05:59 PM »
Oh wow. I saw one picture of it with no caption... I assumed a 4 banger with adapted valve cover.
877
FE Technical Forum / Re: Guess the horsepower on a little pepped-up 390....
« on: November 24, 2018, 07:01:55 PM »
TunnelWedges are indeed cool.
I will guess 558hp at 6800rpm.
I will guess 558hp at 6800rpm.
878
FE Technical Forum / Re: Tunnel Port Intake Gasket/Head Gasket
« on: November 19, 2018, 07:54:59 PM »
Ahh so you are the guy. I love that car. Was hoping it went to a good home and we will see it again before another 35 year hibernation!
Congrats on the cool purchase.
Congrats on the cool purchase.
879
FE Technical Forum / Re: Tunnel Port Intake Gasket/Head Gasket
« on: November 15, 2018, 04:07:23 PM »
Barry, Hi Riser intake gaskets would be useful. Perhaps a filled floor version with a serrated edge knockout piece to use for original height ports?
880
FE Technical Forum / Re: Gas tanks
« on: November 15, 2018, 04:02:50 PM »
If you are creative the tank from a 90's rear wheel drive Chev Caprice is a similiar size, plastic with a built in fuel pump. There are a lot of cars with similar shape strap in tanks with a center rear filler. Check the wrecking yards