Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sixty9cobra

Pages: [1] 2 3 ... 19
1
FE Technical Forum / Re: Intake gaskets
« on: February 28, 2024, 09:57:29 AM »
Backside looks ok front side is sucked in I can see the blue stripe about a half inch into the port. No sign of oil I guess it gets washed out or distributed everywhere when there’s high vacuum. I will pull the intake this week.exhaust is totally wet and back panel  of car has wet spots of oil.

2
FE Technical Forum / Re: Intake gaskets
« on: February 27, 2024, 03:43:09 PM »
Looks like my oil burning situation is caused by printo leaks number four intake gasket is sucked in. I looked down the intake with a bore scope. Spark plugs show no oil yet the exhaust system is coated like an oil burner.  Thank you for sending the gaskets Barry R. I will be ordering a couple of sets and paying you for the one that you sent.

3
FE Technical Forum / Re: CVR water pump question
« on: February 27, 2024, 03:29:02 PM »
CVR replied small block pump is the same as  8000CL and comes with the lower nipple. Cheaper to buy the small block one and toss the wings and put Jays on. Lesson learned.

4
FE Technical Forum / Re: CVR water pump question
« on: February 26, 2024, 09:54:53 AM »
I emailed CVR since that’s the only contact info not even a phone number.

5
FE Technical Forum / CVR water pump question
« on: February 25, 2024, 10:05:57 AM »
I ordered a CVR 8000cl 55 gpm water pump in November and the delivery date was March 15 2024 now it says April.  I was looking at the small block pump 8560cl which is also 55 gpm and its 27 dollars more than the bare pump and it is in stock. Are all the pump and motors the same? Someone on here must have a small block. I could unbolt the stock brackets and bolt on Jays Brackets

6
FE Technical Forum / Re: Battery fuse
« on: January 24, 2024, 11:51:59 PM »
Ok Ill install the fuse and if it's a problem I remove it, Lots of knowledge on here thanks for the opinions.

7
FE Technical Forum / Re: Battery fuse
« on: January 23, 2024, 09:20:50 PM »
I ran 1/0 gauge.

8
FE Technical Forum / Battery fuse
« on: January 23, 2024, 08:05:43 PM »
I had to move my battery to the trunk to make room for a bigger radiator. I put a Moroso shut off on the battery box. I was wondering if I should put a fuse close to the battery. I have a 200amp fuse do you think that would be big enough to crank a 464 with a Robbmc starter?



                                      Harry

9
FE Technical Forum / Re: electrical connectors
« on: January 02, 2024, 12:23:03 PM »
I believe the connectors are metri-pack 630 10-12 gauge wire 46 amps 4 connectors 25 bucks on amazon

10
FE Technical Forum / electrical connectors
« on: December 29, 2023, 07:57:46 PM »
I bought two Spal fans which have connectors on the end. I've been looking for them and can only find them with 8 feet of wire for 49 bucks each I need two. The part number is SBL-YAC-PT which comes with 8 feet of wire for 48 bucks each. I believe it's a 40-amp plug. I'm tempted to just cut it off and move on but it would be nice to be able to unplug them.

11
FE Technical Forum / Re: CVR water pump dimensions
« on: December 29, 2023, 09:59:07 AM »
Thats good news Brent I thought the supply issues were over..

12
FE Technical Forum / Re: CVR water pump dimensions
« on: December 28, 2023, 10:09:42 PM »
Thank you Jay that helps a lot. I can proceed now without knowing that I’m not wasting my time.

13
FE Technical Forum / CVR water pump dimensions
« on: December 28, 2023, 05:14:46 PM »
 Hi, guys, I am upgrading my cooling system with a triple pass crossflow radiator. I am using two Spal 12-inch fans. I also ordered Jays water pump adapters for the CVR pump. The pump won't be available till March. There doesn't seem to be a lot of room in there. Can someone give me the dimensions mostly the height or the distance from the block mount to the tip of the motor, and the diameter of the motor? 

                                Thanks in advance Harry

14
FE Technical Forum / Re: Intake gaskets
« on: December 21, 2023, 11:14:20 PM »
I got the gaskets Barry Thank You they look great.

15
FE Technical Forum / Re: Intake gaskets
« on: December 07, 2023, 06:17:51 PM »
Thank you for the link. I wonder how easily they can be trimmed?

Pages: [1] 2 3 ... 19