News:
SMF - Just Installed!
| Subject / Started by | Replies  / Views |
Last post | ||
|---|---|---|---|---|
| Urgefor and 3 Guests are viewing this board. | ||||
|
|
CAMMERS ON FUEL
Started by HolmanMoodyStroppeGang |
8 Replies
3790 Views |
July 09, 2016, 06:42:43 PMby Qikbbstang |
|
|
|
Open spacer on a 427 Dual quad MR intake?
Started by 427LX |
8 Replies
3607 Views |
June 20, 2016, 06:27:22 PM by Joe-JDC |
|
|
|
Service block
Started by fairlanegt427 |
8 Replies
4117 Views |
June 06, 2016, 08:14:34 PM by fairlanegt427 |
|
|
|
Question about the rear cam seal.
Started by Yellow Truck |
8 Replies
3710 Views |
May 31, 2016, 06:56:46 PM by 66FAIRLANE |
|
|
|
8 Replies
2680 Views |
October 24, 2018, 11:09:06 PM by olman |
|
|
|
|
shaft wear questions....
Started by westcoastgalaxie |
8 Replies
3796 Views |
May 27, 2016, 04:11:10 PM by westcoastgalaxie |
|
|
|
Oil Pan Swap - Pump Pickup Tube Adjustment?
Started by CV355 |
8 Replies
1511 Views |
February 26, 2021, 08:43:24 AM by CV355 |
|
|
|
NOS 427 SOHC cam spec question
Started by 338Raptor |
8 Replies
1822 Views |
June 16, 2020, 09:34:17 PM by 338Raptor |
|
|
|
Check Out This Sonic Test
Started by mbrunson427 |
8 Replies
2928 Views |
April 16, 2018, 11:38:07 PM by Stangman |
|
|
|
Jog my memory - Erson Adjusters
Started by DuckRyder |
8 Replies
1788 Views |
July 05, 2020, 08:23:49 PM by Nightmist66 |
|
|
|
8 Replies
4102 Views |
June 29, 2014, 07:36:09 PM by fe66comet |
|
|
|
|
Help indentify this pan
Started by 57yblock |
8 Replies
3966 Views |
April 26, 2013, 10:46:21 AM by fe66comet |
|
|
|
Factory rocker arm adjusters
Started by KMcCullah |
8 Replies
4683 Views |
April 28, 2013, 04:56:56 PM by MT63AFX |
|
|
|
Fun with weights and math
Started by My427stang |
8 Replies
6089 Views |
July 12, 2012, 10:02:40 PM by My427stang |
|
|
|
Any difference between auto and manual trans cranks?
Started by plovett |
8 Replies
2143 Views |
October 19, 2018, 12:44:12 PM by 1967 XR7 GT |
|
|
|
Head question I should know, but don't
Started by My427stang |
9 Replies
2586 Views |
October 28, 2020, 07:27:02 PM by 427John |
|
|
|
bending pushrods?
Started by stuart olson |
9 Replies
2763 Views |
August 13, 2017, 11:02:18 PM by fryedaddy |
|
|
|
Bolt through the motor mount
Started by Bolted to Floor |
9 Replies
3577 Views |
August 04, 2017, 10:52:23 PM by Bolted to Floor |
|
|
|
6an ptfe fuel line big enough?
Started by Saltshaker |
9 Replies
2400 Views |
October 10, 2020, 06:59:11 AM by djburton |
|
|
|
9 Replies
1240 Views |
April 19, 2023, 05:14:59 PM by Katz427 |
|
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll