31
Non-FE Discussion Forum / RockAuto discount code.....
« on: May 24, 2019, 10:48:55 PM »
good till 7-21-19 109450124103563300 happy shopping...........Tom
Dedicated to Building and Racing the Ford FE Engine
News:
SMF - Just Installed!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
32
Non-FE Discussion Forum / BG220HR FUEL PUMP.........
« on: May 12, 2019, 07:57:27 PM »
Anybody here ever run one of these pumps on the street??? Was going to let a friend put it on his car but have heard conflicting results, good ,bad, inbetween,..TIA...........Tom
33
FE Technical Forum / Re: Trick Flow Tunnel Wedge ?
« on: April 19, 2019, 05:40:41 PM »
I talked to the rep @pri down @ indy and he told me he 'thought' it may be avaiable sometime in may.....
??
??
34
Member Projects / Re: Upgrades to my R-code Mach 1...
« on: April 19, 2019, 05:32:41 PM »
Doug, looks great!!! If I might ask what did you use for underlamit under the carpet, I still need to buy some for my project car and just wondered.. thanks.........Tom
35
FE Technical Forum / Re: FE Power Cylinder Heads
« on: March 15, 2019, 10:06:37 PM »
WOW Jay, that head is totally knocked outta the park, thanks for going above and beyond the call of duty, now I need a towel to clean the "drool" off the keyboard............Tom
36
FE Technical Forum / Re: Valve to bore clearance...........
« on: March 03, 2019, 09:19:59 PM »
Mr.Jack, I did talk with you about that @ DW2017 down @ Cordova, I guess its a go!! Hopefully You can get the new heads figured out for the mustang...Good luck.............Tom
37
FE Technical Forum / Re: Valve to bore clearance...........
« on: March 02, 2019, 08:05:32 PM »
Brent, if we go with door #1 the lift is .700/.688 Do you think that .020 is enough valve to bore clearance??? Thanks....Tom
38
FE Technical Forum / Valve to bore clearance...........
« on: March 02, 2019, 11:45:44 AM »
Motor is 428 @ 4.160 bore, has not been honed for pistons yet, with head on block with exh. valve pushed till retainer hit the guide there is .020 clearance between the valve and bore. The heads are Edelbrock 6005 with 1.750 exh. valves. Our question is will it work like this or should we take a little off the valve. I'm helping a friend and we want the motor to run good. It will be a 462 stroker any thoughts, Blair,Brent , anyone..........Thanks.............Tom
39
Member Projects / Re: Carburetor madness by Drew
« on: March 01, 2019, 05:48:05 PM »
Drew, I have a friend that is interested in a 390'GT' carb, would you have a number that he could call you at? thanks..............Tom
thanks..............Tom
40
FE Technical Forum / Re: Another FE roller lifter question...........
« on: February 10, 2019, 09:39:23 PM »
Yes Brent wanted to go hyd lifters for less maint. , Oh well put the solids back in thanks,..............Tom
41
FE Technical Forum / Re: Another FE roller lifter question...........
« on: February 10, 2019, 11:04:15 AM »
Brent the .050 is 265/272 its an Oregon that Ken use's if the customer is looking for 600 or more horse, he did say it was fairly quick on the ramps, 110 lobe center 106int/cl......... And thanks to all who responded..................Tom
42
FE Technical Forum / Another FE roller lifter question...........
« on: February 09, 2019, 09:40:52 PM »
Can a hyd. roller lifter safely be run a solid roller stick??? Lift is about 700/680 Has any builders safely did this?? Brent, Blair, Jay anybody, Now let me duck out of the way before the trash flyes...........Tom
43
FE Technical Forum / Re: Guess the horsepower....
« on: January 19, 2019, 10:37:27 PM »
I say 635.4 uncorrected
44
FE Technical Forum / Re: Got it hooking again
« on: October 13, 2018, 09:40:30 PM »
Afret, couple of questions.....what did the car run and does it have a 735 carb?? thanks..............Tom
45
Non-FE Discussion Forum / Re: Drag Week 2018 is underway.
« on: September 10, 2018, 08:14:25 PM »
Kevin, thanks for the update....Did you happen to hear what Jack Miller ran with his mustang??? thanks..........Tom