Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - cattleFEeder

Pages: 1 [2]
16
Non-FE Discussion Forum / Funny sign
« on: May 21, 2019, 04:31:40 PM »
I had a retired ford mechanic rebuild my FMX transmission out of my 70 cougar eliminator. I went and picked it up today and this was the sign on his shop.

17
Non-FE Discussion Forum / 65 galaxie with 427 SOHC coming up at auction
« on: May 16, 2019, 06:02:58 AM »
Those little tires would shred in no time.
http://fordauthority.com/2019/05/1965-ford-galaxie-500-cammer-no-reserve-auction/

18
Private Classifieds / Holman/Moody tunnel port engine
« on: April 06, 2019, 09:19:08 AM »
Seen this in hemmings, not mine and no other info.
https://www.hemmings.com/parts/item/16780.html?refer=saturday

19
Non-FE Discussion Forum / 428 Fe in a camaro
« on: September 29, 2018, 06:37:01 AM »
I saw this over on the 7173 mustang board and had to share it.
https://www.7173mustangs.com/thread-428-camaro

20
Non-FE Discussion Forum / Top loader question
« on: January 30, 2018, 12:57:20 PM »
As I was on one of my many  winter projects, I was measuring up a new drive shaft on my 71 torino cobra. I noticed the top loader didn't have a drain plug, every other one I have owned has had a drain plug. Were they added later by the dealer or owner? The tag on the side is
RUG AU1 012755

21
FE Technical Forum / Header studs
« on: November 13, 2017, 10:07:51 PM »
What is the downside to using studs to mount headers?
Do you use bluelocktite , or hand tighten them?
Does it matter if the heads are cast iron or aluminum.

22
FE Engine Dyno Results / 520 FE Dyno results
« on: September 29, 2017, 08:02:27 PM »
https://youtu.be/qv4JBpR9iy8
https://youtu.be/8ehtdzlL-QM

Once I get all the build sheets I will post more.
Thanks to Jay and Brent for their in help in this build. Dan

23
FE Technical Forum / 520 FE on a simtester
« on: July 11, 2017, 06:31:28 PM »
Here is a video of my 520 FE on a simtester, being built by TMeyer in Fairmont MN.
Tim is a ford guy that does a lot of 351C and 400 engines.
My engine is a BBM block, cnc heads and their 2X4 intake.
https://youtu.be/CU3ok2z1FoE

24
FE Technical Forum / Solid lifters
« on: September 14, 2016, 08:38:42 AM »
Are there any reasons to run a flat tappet lifter over a solid roller lifter on the street?
The block is not drilled for a hydraulic cam, its a factory block being stroked to 482 cubes.

25
FE Technical Forum / 427 side oiler date code
« on: August 24, 2016, 09:24:43 PM »
Does anybody know how to decipfer this block ?

26
FE Technical Forum / PCV for a low riser 2X4
« on: May 03, 2016, 06:28:42 AM »
Should I try getting a pcv valve hooked up to vent tube  on my manifold, I have  pentroof valve covers? Right now it just vents out under the car. I was going to just hook up to the rear carb , will that work?

27
FE Technical Forum / Pro Maxx Heads
« on: November 24, 2015, 08:25:45 PM »
http://www.jegs.com/p/ProMaxx-Performance/ProMaxx-MAXX-Series-Ford-FE-Aluminum-Cylinder-Heads/3462220/10002/-1

What am I missing, have these heads been out for a while? I never heard of them.

28
FE Technical Forum / Replacing intake bolts
« on: July 13, 2015, 09:49:06 PM »
I was going to replace the intake bolts on my 390 with a streetmaster intake, whoever installed them just used regular grade 5 bolts with no washers. I am using an ARP kit for the replacement. Whats the best way to do this so I don't get an intake leak? I was planning on doing 1 at time and retorque them to 25 lbs as I go, will this work?

Pages: 1 [2]