Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Saltshaker

Pages: 1 2 3 [4]
46
FE Technical Forum / Pressure plate recommendation
« on: October 25, 2018, 01:42:56 PM »
My pressure plate with a Hyd slave has become to hard to push. Ram 406 3 finger pressure plate, any suggestions? 2600 lb replica Cobra with 428
Jon

47
FE Technical Forum / Clutch Question
« on: October 19, 2018, 08:25:48 PM »
Any run a Spec clutch aNd pressure plate SF272 stage 2....it’s good for 500ft lb torque?
Jon

48
FE Technical Forum / Camshaft Question
« on: October 08, 2018, 11:49:31 AM »
Anyone have a measurement how far below the China wall the cam is? Trying to measure instant center on car
Jon

49
FE Technical Forum / FE expansion tank question
« on: August 10, 2018, 12:23:30 PM »
Days after I drive my car if I start to take the radiator cap off the tank still has pressure in it. Is this normal?
Jon

50
Private Classifieds / FS:48ida Webers and intake for FE
« on: July 30, 2018, 10:06:31 PM »
Posting for a friend;
Bought from Jim Inglese
48ida carbs on a powder coated intake(aluminum color)
Intake has hidden vacuum lines for power brakes
Includes linkage, short volicity stacks, braided fuel lines,extra jets
Set up for a 454ci FE...$3200 plus shipping from Nj
Pictures available ....send email
Jon
Jonk5152@yahoo.com

51
Private Classifieds / Erson Rocker parts
« on: July 23, 2018, 07:40:09 PM »
Looking for a friend; need a rocker shaft and stand with bolt for oil feed
Jon

52
FE Technical Forum / Couple of problems
« on: June 16, 2018, 10:06:24 AM »
My fan belt to the alt always needs to be adjusted... every  thousand miles. Replaced it last yr, 1 grove pulley.
Car has become hard to start taking 3-5 tries... timing 18int and 38 total this is a new problem... car had been Always for 6wks. Plugs look good
Jon

53
Private Classifieds / Shift rods/Mounting Plate/ more
« on: March 21, 2017, 04:47:50 AM »
Set of shift rods (look orignal) for a toploader...have a little surface rust $40 plus shipping
Hurst mounting plate $20 is plus shipping
Shift tangs $15 plus shipping
Timing chain cover $25 plus shipping
Harmonic balancer off my 428 rubber has some cracks $10 plus shipping
Single water pump pulley $15 plus shipping
Innovative Motorsports LM2 Wide Band Air/Fuel Ratio Mrter,instructions,O2 Sensor, Power Cable...$200
Plus shipping
Pictures available
Jonk5152@yahoo.com
Jon

54
Private Classifieds / Holley 850 Vac Secondary Carb
« on: July 14, 2015, 07:48:04 AM »
Selling for a friend, Manual Choke, less then 100 miles on it... To big for his motor $250 plus shipping from Harrisburg, PA
Jon

55
FE Technical Forum / 2 intake gaskets 1 side
« on: November 09, 2014, 09:46:21 PM »
When using 2 gaskets on one side does that change the gemonerty of the push rods and the intake?
Does the intake need to be clearenced for the pushrods?
Jon

56
FE Technical Forum / 10-30wt vr1
« on: March 24, 2014, 06:37:44 AM »
Is it ok to use 20-30vr1 in a 428 factory crank and rods?
Jon

Pages: 1 2 3 [4]