Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Saltshaker

Pages: 1 [2] 3 4
16
Private Classifieds / what’s this worth?
« on: July 23, 2020, 08:25:51 PM »

what is a TKO600 road race trans .082 od with a speed shifter, Lakewood Bell housing(bottom cut for a Cobra) hyd clutch slave w/mounting bracket and 7/8 MC, fork plus a fly wheel new clutch disc and 3 finger Ram pressure plate?
Jon

17
FE Technical Forum / fuel line question
« on: July 15, 2020, 06:50:35 PM »
what size fuel line is needed...3/8 or 1/2”? I can get a tank pick up for both. Engine is 411 rwhp with a Carter mech pump. Both outlets are 1/4ntp. Is it worth having a return line to the tank with a Mech pump?
Jon

18
FE Technical Forum / AOD transmission behind a FE
« on: June 28, 2020, 04:17:45 PM »
Anyone install a aod trans on there FE? I currently have a TKO600 and thinking I might want  to swap for a AOD .Is  there  one about the same size as a tko600?
Jon

19
FE Technical Forum / pinion angle
« on: June 13, 2020, 10:01:49 AM »
can the pinion angle be measured off the oil pan rail? is the pan rail parallel to the crank?
jon

20
Private Classifieds / FS Street Master
« on: May 22, 2020, 06:16:00 PM »
Very good condition with no striped threads or welds
Pictures on request
$280 plus shipping from Nj
jon
SOLD

21
FE Technical Forum / electric clutch Slave
« on: May 10, 2020, 06:35:06 PM »
has anyone used a electric clutch slave on their car?
jon

22
FE Technical Forum / Fuel system
« on: February 08, 2020, 05:19:58 PM »
Building a new Cobra that uses a gas tank from a early Comaro/Firebird. Is there any advantage to drill and weld a pickup from the bottom of the tank? I could use the original pickup as a trturn line.
Motor is a 428 with a Carter Mech Pump. In my other Cobra I need a electric pump so it would pull in 3rd & 4th on the track.
Job

23
Member Projects / Dummy FE Block
« on: November 20, 2019, 04:47:48 PM »
Any one near NJ have a plastic dummy block I could borrow for a day?
Jon

24
FE Technical Forum / Lakewood bellhousing
« on: November 02, 2019, 11:19:15 AM »
Does it need to be dialed in? Pull the motor, had Rob Mcqu down pins and 1 is now missing
Jon

25
FE Technical Forum / Paint burns off heads
« on: October 27, 2019, 02:32:04 PM »
I have painted my heads several times. Always prime them and a couple of coats of rattle can blue...even had a shop spray them. The paint always burns off the exhaust ports, WHY?? Is their a better product or way to do this? Motor is out of the car...
Jon

26
FE Technical Forum / Heavy Clutch
« on: October 25, 2019, 06:49:09 AM »
I’m having a issue with the clutch being to hard to push on the ball of my foot, I have neuropathy in my left foot. I’m using a 3 finger Ram pressure plate...7/8 mc with a 1” slave. I know I can change the Mc but would a different style pressure plate it throw out bearing make a difference?
Jon

27
FE Technical Forum / How many miles will solid lifter cam last
« on: October 22, 2019, 04:52:41 PM »
I have the engine out of my car, the cam has 28k miles on it and runs great. Is it worth pulling it and put a hyd roller on it?
Jon

28
Private Classifieds / WTB; Running 390
« on: October 13, 2019, 04:31:27 PM »
Looking for a running 390 to put in a 4 speed car near NJ
Jon

29
Non-FE Discussion Forum / Shipping a non running car
« on: October 07, 2019, 05:16:24 PM »
Thoughts on shipping a small non running car San Francisco to NJ
Any idea what it would cost?
Jon

30
FE Technical Forum / Shift light/rev limiter settingd
« on: September 16, 2019, 07:06:55 PM »
428 on the dunk made power to 5950rpm...so where would you set the rev limiter and shift light?
Jon

Pages: 1 [2] 3 4