Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 475fetoploader

Pages: [1] 2 3 ... 27
1
Drag Strip Results for FE Powered Vehicles / Re: Final TNT for season at local track
« on: November 06, 2023, 08:28:11 AM »
I was going to throw my 2 cents in, and tell you about my 295/65/15 that fits snug, but fits. I have ladder bars though. So all the issues caused by leaf springs, aren’t there.

2
FE Technical Forum / Re: FE Crane cam id
« on: November 06, 2023, 08:24:34 AM »
I would think the idle produced by this cam would be pleasant.

3
Non-FE Discussion Forum / Re: Lithium Ion jump starters
« on: August 15, 2023, 11:20:20 PM »
We have several of the NOCO boost units. They are extremely impressive, can usually handle 15-20 dead batteries in a short amount of time.  Plus they have a light, if you’re in the dark.

4
FE Technical Forum / Re: transmission options
« on: May 02, 2023, 08:37:48 AM »
Ok, the TKX with modifications has my attention. How bad do you have to butcher a 67 Fairlane trans tunnel though?

5
FE Technical Forum / Re: transmission options
« on: April 30, 2023, 09:40:57 PM »
Hightower 4 speed.

6
Good Deals! / Re: Brent Lykins gave me a good deal
« on: April 27, 2023, 09:20:24 PM »
Brent ordered me a hydraulic roller for my truck engine.  This build surprised everyone on the dyno. No doubt this cam made the difference for me. Thanks!

7
FE Technical Forum / Re: NW Machine shops
« on: March 09, 2023, 01:59:30 PM »
Bliss was probably the best sbf guy I’ve known of, but not sure he’s even doing stuff at home anymore.  Gary Pugh was really good, he’s retired.  Dale Green may be doing stuff at home now.  If you don’t have it, I could probably scrounge up a cell number for him, he’s somewhat of a family friend. 

8
FE Technical Forum / Re: NW Machine shops
« on: March 09, 2023, 12:13:58 AM »
Auburn Auto machine, Auburn Washington. But they’re busy always.
Britco, down in Centralia I trust them.
Dale Green, but he’s looking for a building at the moment I believe.
Auburn Auto machine did a 428 block for me, they’re great there, meticulous, however they’re backlogged sometimes 6 months also. 

9
Non-FE Discussion Forum / Re: '67 f250 repaint... roof right now
« on: March 01, 2023, 11:23:41 PM »
Looking good!

10
Non-FE Discussion Forum / Re: I quit drinking
« on: January 09, 2023, 06:50:09 PM »
That’s great to hear.  One day at a time my friend. I’m a bit over 5 years now. When people ask why I don’t drink, I tell them I did 20 years of research to prove I don’t drink like a gentleman.  Keep up the good work.

11
FE Technical Forum / Re: 427 questions
« on: December 25, 2022, 11:30:52 PM »
Can you fly cut the pistons safely? Remove compression, leave enough material still?

12
FE Technical Forum / Re: Dick Brannan
« on: October 15, 2022, 03:25:31 PM »
There’s a great book detailing his career. Thunderbolt by Charles R. Morris. Quick read 100 pages or so.

13
FE Technical Forum / Re: still playing guess the horsepower?
« on: October 05, 2022, 01:46:31 PM »
ran it yesterday 530/600

14
FE Technical Forum / Re: still playing guess the horsepower?
« on: October 05, 2022, 09:15:17 AM »
NP435, 205 transfer case.  Dana 60 king pin front, Dana 70 rear.

15
FE Technical Forum / Re: Best battery for 427 with alternator?
« on: October 05, 2022, 09:13:02 AM »
Odyssey

Pages: [1] 2 3 ... 27