Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Leny Mason

Pages: [1] 2 3 ... 25
1
FE Technical Forum / Re: 427 SOHC blower manifold question
« on: February 05, 2024, 09:56:26 AM »
I cut down a FE distributor housing and put a bearing in it and setscrewd in place there is not much room under the manifold, make sure You put the right gear to match the cam you are running

2
Member Projects / Re: '66 Falcon Gasser
« on: January 16, 2024, 09:17:19 AM »
Love it gasser's are so fun!!!!

3
Member Projects / Re: 67 Mustang Pro Street
« on: January 16, 2024, 09:14:12 AM »
How Cool the pictures are so big I can not see it all though, how big is your alternator to run all the system and power steering, love it.

4
FE Technical Forum / Re: C6 calibration
« on: November 29, 2023, 07:52:35 PM »
Thanks Heo it is starting to be a lot of fun, it took forever but it was worth it, it drives great I have never drove a fat tire car before.

5
FE Technical Forum / Re: C6 calibration
« on: November 29, 2023, 09:40:34 AM »
Will do thanks for the help. Leny

6
FE Technical Forum / Re: C6 calibration
« on: November 29, 2023, 04:20:03 AM »
Thanks' for all the information, it is Cool the there is so many people on this sight that have all this information in there heads Thanks' again. Leny

7
FE Technical Forum / Re: C6 calibration
« on: November 29, 2023, 04:06:32 AM »
The C6 speedo gear on the output shaft is not removable.
The teeth are rolled into the shaft itself.

Shafts were made with 6-7-8-9 teeth for the speedo.

To change the output shaft you need to remove and dis-assemble the trans.

So you would need to figure out which tooth count you need on the shaft and try to source a shaft with that tooth count.
Then take the trans apart to change it.

I don't know of a chart to find tooth counts.

You might get "close" just changing the driven cable gear.   Thanks I will experiment I found a 16 driven gear.

8
FE Technical Forum / Re: C6 calibration
« on: November 29, 2023, 04:03:26 AM »
See if this helps...
https://www.428cobrajet.org/speedo-calc
   

That is cool if My driven gear is 8 I need a 21 driven gear thanks.

9
Member Projects / Re: 1964 Comet Blown injected Cammer
« on: November 28, 2023, 08:47:58 AM »
I have the stock fuel pump but it is not on the engine I am running Weldon fuel pumps one For Fuel and one for Water Meth.

10
FE Technical Forum / C6 calibration
« on: November 28, 2023, 08:42:21 AM »
Is there anyone Here that has a chart to figure what tooth count for C6 speedometer, I have 325 gears and 33 inch tires in My Comet, I don't know if there is different amount of teeth on the tale shafts on different C6's thanks Leny.

11
Member Projects / Re: 1964 Comet Blown injected Cammer
« on: November 23, 2023, 11:52:41 AM »
Hi, yes I am concerned about that we are shutting the solenoid and the pump at intervals it is though it is siphoning it I have had it with that so I am putting fuel to cool it.   

12
Member Projects / Re: 1964 Comet Blown injected Cammer
« on: November 23, 2023, 10:34:45 AM »
I have been driving it a lot, I need to do something different about cooling the blower, I have a water meth system squirting just above the blower to cool it but it is liking it to much, I have been going through six gallons every fifty miles I plugged off half of the injectors and I am still using two gallons in fifty miles, so I am going to put four Small injectors and and run them at twenty percent of the time with gasoline and see what happens, but it is way more fun to drive then building it, I was tired of working on it by for now Leny.

13
Member Projects / Re: 1964 Comet Blown injected Cammer
« on: October 18, 2023, 08:49:33 AM »
Thanks t is running very nice and drives good, it has taken a while to work some bugs out but fun, I am glad I went with 325 gears the power is manageable with 3500 stall, maybe when I get used to it I can go with lower gears.

14
Member Projects / Re: 1964 Comet Blown injected Cammer
« on: October 15, 2023, 08:52:20 AM »
I got top ten at the show yesterday, there was some great cars there, it was fun when We left there was a lot of people wanting to hear it run!!

15
Member Projects / Re: 1964 Comet Blown injected Cammer
« on: October 12, 2023, 09:55:22 PM »
Yes it was a rush for a little while , but were I was at the time it couldn't of been a better place.

Pages: [1] 2 3 ... 25