1
FE Technical Forum / Re: hyd roller lifter on a solid roller cam?
« on: November 26, 2012, 05:56:49 PM »
Thanks Mr. Jay. I lost the comp lifter and went back with crower lifters im still worried though Thanks for the response!!
Dedicated to Building and Racing the Ford FE Engine
News:
SMF - Just Installed!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
FE Technical Forum / hyd roller lifter on a solid roller cam?
« on: November 25, 2012, 08:42:56 PM »
I lost a comp roller lifter bearing. I pulled the cam and comp reground it for me. Im running crower solid roller lifters on it. Im worried i will have another failure. Im running this on the street. I wish i would have gone hyd roller from the start. Ive heard some say you can run hyd roller lifters on some solid roller cams. Is this possible? Thanks for any responses!!
3
FE Technical Forum / MSD pickup coil Bad?
« on: June 10, 2012, 10:03:06 AM »
Well i got my fuel problems fixed and went out to start the truck sat morn and no spark. I had trouble last weekend too. I thought it was the 2pin connectors on the pick up. I cut them and used some crimp on connectors to replace them. This is a new pro billet 8594. Any way i pull the coil wire and ground it and crank the motor and no spark. I then jump the 2 wires going out to the box and it sparks fine. Got to be the pickup? Right? I also ohmed it with my fluke and im getting 250ohms. Im pretty sure its the pickup do yall have any suggestions. Im gonna call msd tommorrow. Thanks!
4
FE Technical Forum / Re: fuel vapor in fuel line?
« on: June 10, 2012, 09:56:11 AM »
Thanks guys I insulated the lines with armaflex wrap and it fixed the problem completely. Thanks again!
5
FE Technical Forum / Re: fuel vapor in fuel line?
« on: June 06, 2012, 07:28:04 PM »
Thanks guys for the responses. I will insuate it and see what happens. Sounds like that will fix it. Thanks!
6
FE Technical Forum / fuel vapor in fuel line?
« on: June 05, 2012, 07:17:11 PM »
Hey guys can you tell me at what temperature gas boils at? I have a 76f100 with the original fuel line coming from the tank. It runs along the frame rail pretty close to my headers, to the pump and up to the carb in front of the motor. The line gets HOT i think fuel has to be changing state on me. I just splashes a little in the filter. I checked the line its not stopped up and the vent is open. Im thinking about insulating it. What do yall think?
8
FE Technical Forum / Re: fuel pump eccentric
« on: May 27, 2012, 05:10:24 PM »
Thanks Mr. JAY I have to get a 2in muffer clamp to get the crank spacer off. Is there a trick to get the dowel out of the cam. I should'nt have to pull the cam out i hope. Thanks for all the advice it helps alot!!
9
FE Technical Forum / Re: fuel pump eccentric
« on: May 27, 2012, 11:17:52 AM »
Thanks Mr. Barry. I don't think my dowel goes thru to catch the eccentric. I think it is too short. I just have a hole in the sprocket. Can i get a longer dowel to tap in the hole and loctite?
10
FE Technical Forum / fuel pump eccentric
« on: May 26, 2012, 08:51:13 PM »
I think my one piece eccentric came loose, i don't remember the longer dowel going into the oblong hole. I have a 2piece eccentric and i heard you can put a washer behing it to get the outer ring some clearance. I have a comp chain set. Im gonna pull the cover off this week and check it out. Do you think the 2piece will work with the washer behind it? Thanks
Pages: [1]