Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Faron

Pages: [1] 2
1
FE Technical Forum / Childs and Albert replacement capscrew torque specs
« on: November 04, 2022, 08:47:40 PM »
I have a st of leMans rods with C&A cap screws any idea of torque numbers

3
FE Technical Forum / E-85 who is running it and questions
« on: January 07, 2022, 05:57:41 PM »
What lines are ok , can you run an aluminum cell , maintenance and carb mods needed

4
FE Technical Forum / Ring Spacers
« on: October 13, 2020, 03:14:09 PM »
Does anyone make ring spacers for the old TRW flat top 390 Pistons that would allow a better ring package , if so who, and  how much , the 5/64, 3/32, 3/16 combo is a bit dated , I have nice .040 Pistons I want to use but that ring package limits me

5
Pressing News . 2020 FERR will have a date change to September 9,10,11,12
With all the travel restrictions and the fear of infecting any of the legends and or racers or spectators of this great event we are moving this to September 9,10,11,12 with the 13th as a rain date
Everything on the flyer will stay the same and were almost have all of the legends notified as of the change. Thank you for your support and understanding . Any questions message me. Mike McCracken

7
FE Technical Forum / Latest updated Flyer FE Race and Reunion
« on: February 07, 2020, 02:13:41 PM »
Be There if You Can

8
FE Technical Forum / Intake Pushrod hole repair
« on: July 11, 2019, 02:32:54 PM »
In 1996 I opened up the push rod holes in my blower intake , sadly I broke through into the intake port on a few, i used PVC Pipe and JB weld ( not optimum but it held ) , fast forward to now , they are finally leaking and allowing Oil to be drawn in , looking for advise , and where to get tubing to repair the holes and what kind of sealer to use on them

9
FE Technical Forum / FE Race an Reunion BSD Flyer
« on: February 22, 2019, 01:05:29 PM »
See You End of April !!

10
Private Classifieds / MSD Dist ( SOLD )
« on: February 18, 2019, 12:18:46 PM »
MSD Dist part number 8594 that is barely Used will sell for 265.00 curved to your door (SOLD SOLD)

12
FE Technical Forum / Fuel Pump Ecentric
« on: April 23, 2018, 08:41:56 AM »
Planning on adding a Mech Fuel pump to my car , I jave a few Ecentrics , how can I tell if is for an FE ( havent had a Mech Pump on the car since the early 80"s ) LOL

13
Private Classifieds / FE to C-4 Bell wanted
« on: March 21, 2018, 09:11:27 PM »
Anyone have an extra or one to  sell

14
FE Technical Forum / Jay , What is the Stroke on your cammer Combo ?
« on: November 25, 2016, 10:49:32 PM »
Just seen an article with a 4.75 , but I thought yours was over that

15
One More Month,Continuing through Oct , Special offering Brand New Small Cap Duraspark Distributors
$225
Freeburg, PA (17827)

These are all New Units, no core needed , Small Caps ( large caps adapters and Rotor are 39.00 more ) With cast Iron Gear , Steel Gears, are 75.00 more ( roller cams ) Curved to your Combo , shipped to your door ( continental 48 ) 225.00 I take PayPal and USPS Money Orders , approx 9 working Days wait after receipt of Payment E-mail me at
TotalPerfEntofPa@aol.com addedum , I also have other Ford Family Dists SBF and 335/385

Pages: [1] 2