1
FE Technical Forum / Ford FE C7SF-12127-A distributor application?
« on: March 02, 2024, 11:01:12 PM »
Can anyone here tell me what a C7SF-12127-A distributor was originally for?. Thanks
Dedicated to Building and Racing the Ford FE Engine
News:
SMF - Just Installed!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Private Classifieds / NOS autolite spark plug wire on the autolite loom roll
« on: February 02, 2024, 12:46:50 PM »
The loom reel says part# 16- P-C-7 100ft, loom is half full or more. Date code on the wire itself it 2-Q-66. $200 obo
3
Private Classifieds / NOS 390gt/428cj camshaft
« on: January 30, 2024, 12:48:18 PM »
This is a regrind from Colt Cams in Vancouver,BC. Stock specs new, never installed.$100
4
Private Classifieds / 66-69 fairlane Torino FE engine/ trans mounts
« on: January 30, 2024, 10:11:27 AM »
I have a set of FE frame/engine mounts for 66-69 Torino/fairlane, include rubber insulators $250
C6/4spd FE transmission cross member $150
#6113 hooker headers, good used $350***SOLD***
I also have rust free doors for 68/69 Torino/fairlane. Prefer pick up( south central BC/north central WA state. $200 each
C6/4spd FE transmission cross member $150
#6113 hooker headers, good used $350***SOLD***
I also have rust free doors for 68/69 Torino/fairlane. Prefer pick up( south central BC/north central WA state. $200 each
5
Private Classifieds / Ford FE Chet Herbert Solid roller camshaft **SOLD**
« on: January 29, 2024, 02:30:06 PM »
Chet Herbert Solid roller camshaft part#GR262 260/270@.050, .705/.705 lift. Brand new never installed, can make a combo deal with the lunati sold roller lifters I also have listed. Asking $350 or reasonable offer..**SOLD**
Thanks!
Thanks!
6
Private Classifieds / 391FT bathtub oil pan/pickup
« on: January 25, 2024, 08:43:54 PM »
391ft oil pan and pickup, also have a couple 4x4 oil pans. $250obo
7
Private Classifieds / 428cj crankshaft std/std and 428cj rods
« on: January 25, 2024, 08:35:18 PM »
428cj crankshaft std/std, at the machine shop but should stay std/std, looked excellent out of a low mile running engine with matching balanced true 13/32 rods. Asking $ 950obo
New NOS std(main and rod)Michigan bearings will be included provided it stays std/ std after the wash/magniflux and light polish and measure. Thanks
New NOS std(main and rod)Michigan bearings will be included provided it stays std/ std after the wash/magniflux and light polish and measure. Thanks
8
Private Classifieds / Ready to run EDC machine chamber heads
« on: January 25, 2024, 08:25:47 PM »
Completely rebuilt, were run very briefly before swapping to edelbrock heads. Stock valve size, no porting but great bolt on heads. $500
9
Private Classifieds / Comp #839-16 solid roller lifters *SOLD*
« on: January 25, 2024, 08:19:58 PM »
Excellent used comp #839-16 solid roller lifters. Went to a solid flat tappet due to early solid only block. Bought here from a forum member. Asking $350. **SOLD**
10
Private Classifieds / Holley 950HP #80498-1
« on: January 25, 2024, 08:12:51 PM »
Holley 950HP double pumper, excellent condition, I would toss a kit in it before running it personally but no damage or nonsense. Spec for methonal, no longer available from Holley. 1100+ new Asking $450
Thanks
Thanks
11
Private Classifieds / Lunati #72903 ford Fe solid roller lifters
« on: January 25, 2024, 08:04:04 PM »
Excellent used lunati # 72903 solid roller lifters. I bought them from Dale P. Here on the forum, very minimal use (40?, 1/4 mile passes?), maybe Dale can chime in, it's been a few years. $325 shipped. Thanks
12
Private Classifieds / Perfect std/std 391ft crankshaft
« on: January 25, 2024, 07:53:15 PM »
D2TE casting 391ft crankshaft. Garunteed std/std ( I have the entire engine if you need any FT parts). $350 obo. Thanks
13
Private Classifieds / Wolverine lightweight solid lifters (NOS)
« on: January 25, 2024, 07:46:20 PM »
I have a set of NOS Wolverine (made by Johnson) lightweight solid lifters, I have never seen another set. Probably made from unobtainium. VERY COOL!. They are scalloped in the body, bases are mint, VERY VERY light dust rust on the pushrod side but otherwise perfect. You may never see another set. I will not sell on eBay,so this is it. Starting to clear my shelves. $200usd shipped
14
Private Classifieds / Jericho 4 spd trans/ ultra lightweight clutch system **SOLD**
« on: January 24, 2024, 02:59:34 PM »
The transmission is freshly gone through, comes with ultra lightweight clutch system,includes 428 add on weight for the flywheel. Never run, as new. Changing direction, will trade for 5 or 6 speed transmission ( no Doug Nash please). 3.08/1.93/1.40/1.00. Serial #8431D4 if you want to phone Jericho. No downsliders, drag race transmission. The clutch system weighs 20lbs total. Fully adjustable, made by 10,000 RPM. It also includes a long inline shifter Thanks
15
Private Classifieds / Holman moody 2x4 MR intake
« on: January 24, 2024, 02:53:08 PM »
Holman moody Medium Riser dual quad, Holman/Moody scripted intake, NOS, never installed. Bought from Lee Holman. Includes original H/M box and invoice from Lee Holman. I just talked to Lee and he said he has no idea if or when they will ever be available again $2000USD or reasonable offer. Free shipping (which is not cheap these days)to the lower 48 or Canada.