Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Leny Mason

Pages: [1] 2 3
1
FE Technical Forum / C6 calibration
« on: November 28, 2023, 08:42:21 AM »
Is there anyone Here that has a chart to figure what tooth count for C6 speedometer, I have 325 gears and 33 inch tires in My Comet, I don't know if there is different amount of teeth on the tale shafts on different C6's thanks Leny.

2
FE Technical Forum / Bowling Green
« on: June 14, 2023, 08:34:37 AM »
Is anyone going to the Hot Rod Reunion In Bowling Green KY this Year?

3
FE Technical Forum / Fuel pump
« on: May 07, 2021, 08:34:52 AM »
The fuel pump started to leak on my 1969 428 CJ Mustang, I am wondering if some one here sells  pumps, I search it here and didn't find any, thanks Leny.

4
FE Technical Forum / Remote filter
« on: February 28, 2021, 03:17:05 PM »
What adaptors are available for a FE to run a remote filter Thanks.

5
Private Classifieds / High riser head
« on: October 21, 2020, 08:31:32 AM »
We are looking for one High riser head,  We found one now we need one more and maybe an Intake thanks Leny Mason.

6
FE Technical Forum / Knock sensor
« on: December 29, 2019, 10:45:13 PM »
Has anyone used a knock sensor on a FE, I talked to Jay and He has not had good readings when He tried them, I do not think you can have a self learning system with out letting it read the detonation knock to take timing out, I know there is a lot of people on here that use different systems, Mine is a Haltech system Thanks for the input. Leny Mason

7
FE Technical Forum / Lifter noise
« on: July 12, 2019, 08:35:16 AM »
A friend built a 390 for a 1969 Cobra clone, when he starts it up it sounds like bad adjusted solid lifters, it has 50 psi oil pressure at start up as it warms up the oil comes down to 40 psi and the lifters start to quiet down one at a time, then you shut it down wait and minute and it starts all over again noisy lifters and then they get quiet again, any Ideas what causes this ? I have never seen this before. Leny Mason 

8
FE Technical Forum / Bowling Green
« on: June 25, 2019, 10:48:38 PM »
I got to meet some of the Ford racers there, Daryl Nelson , D W Hopkins, Dennis White and Rick Kent it was fun to get to know them a little, Rick went 150 MPH then found out he had no brakes in his Pinto, he went into the corn field a long way before he stopped, I would bet it was noisy for a while, He took the front clip off and fixed the brakes and back racing He went, what a fun time We had. Leny Mason

9
FE Technical Forum / Bowling Green
« on: June 20, 2019, 08:07:59 AM »
I got to spend time with Larry Gould, Larry Brown, John Jones telling Ford racing stories, they had the time of there life you can tell listening to them talk about racing for Ford, mostly FE's a lot of Cammer stuff Larry Gould talked about getting all the Sohc parts and engines he needed , what a time they must of had getting paid to blow cammers up, you can see the smiles on there faces it must of been a great time, George Montgomery and his Wife were there to, and looking good selling shirts and telling stories, We had a great time there. Leny Mason

10
FE Technical Forum / test run
« on: June 09, 2019, 08:58:25 AM »
Test Run

11
FE Technical Forum / 67 Mustang with headers and power steering
« on: March 21, 2019, 09:28:27 PM »
We put a 428 in a 67 Mustang with power steering and headers, now that is a joke what the header Company's want you to do to mount the cylinder to the frame, a engineering marvel Has anyone else ran into this. Leny Mason

12
FE Technical Forum / Not the right Cams
« on: March 09, 2019, 01:22:11 PM »
Well My Engine was almost together until we were setting up the cams and found out the cams are not what they are supposed to be, what a disappointment I bought these cams in 2006, that is the problem with taking your whole life to finish a project but everything cost money, but Jay Brown came to the rescue and ordered the right ones for Me, we are coming along with the body work paint job it is black so a lot of sanding, Thanks Jay. Leny Mason 

13
FE Technical Forum / SOHC front cover
« on: January 31, 2019, 09:27:55 AM »
Hi, I am installing My front cover and there is holes in the wrong place on the tin backing plate, on the left head one hole in .250 away from were it should be, and on the right head there is a hole that goes nowhere, my heads have been milled so some holes are off some but my intake fits nice so I am modifying the front cover to fit, they must of made a few different heads that the left head hole is off that far, but if it was easy every one be doing it. Leny Mason

14
Private Classifieds / side oilier main caps
« on: December 30, 2018, 09:43:38 PM »
We are looking for side oilier main cap , for a 1963 block.  Leny Mason

15
Non-FE Discussion Forum / True High Nine differential
« on: December 28, 2018, 09:23:24 AM »
I am told I need to find a True High Nine differential for off road does any one know anything about them, the pinion is high on them is all I know we are looking for one. Leny Mason

Pages: [1] 2 3