Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Saltshaker

Pages: [1] 2 3 4
1
FE Technical Forum / what lb radiator cap w/expansion tank
« on: September 21, 2023, 09:33:49 AM »
what cap is used? can I use a 18lb cap?
Jon

2
FE Technical Forum / popping exhaust
« on: August 07, 2022, 08:22:39 AM »
I have a random popping in my exhaust on the right side. This is in a 427 Cobra with side pipes , the pop is random and happens while driving or idling not while accelerating or the decelerating. I’ve tightened all the bolts on the headers and the slip on side pipes have bolts holding them together any suggestions I don’t see any strike marks from the exhaust.
Jon

3
FE Technical Forum / V Belt tensioner for a FE
« on: July 18, 2022, 08:39:22 PM »
is there a V Belt tensioner for a FE ?
Jon

4
FE Technical Forum / return line to tank
« on: March 18, 2022, 02:51:39 PM »
Warm here today and I’m have a problem with fuel boiling. Will a return line solve the problem? Does it need a by pass regulator or is there another way?
Jon

5
FE Technical Forum / Drain hose on expansion tank
« on: March 16, 2022, 08:55:38 PM »
Where does the drain hose go? Does the hose drain to the ground, back to the radiator or to a recovery tank?
Jon

6
FE Technical Forum / the right stuff or ultra grey seal china wall
« on: December 26, 2021, 03:42:28 PM »
replacing intake gaskets, oil leak back of the china wall. it was originality sealed with the right stuff but now it’s leaking. What have you had the best results with?
Jon

7
Non-FE Discussion Forum / Speedmaster 8 Stack
« on: November 28, 2021, 01:13:08 PM »
Anyone using this system? Is the gas mileage better then running Webers?
Jon

8
FE Technical Forum / Intake leaking oil back of motor
« on: November 20, 2021, 03:58:47 PM »
It is leaking at the back where the intake meets the block. Is there another way to fix it without pulling the intake?
I use “the right stuff “ to seal it
Jon

9
Private Classifieds / 3/8 steel header flanges
« on: October 24, 2021, 09:13:11 AM »
Free! Cleaning out the garage.., just pay shipping from 07746 Nj
Jon

10
FE Technical Forum / Carb Hesitation
« on: July 21, 2021, 06:39:37 PM »
Engine ran flawlessly in my old car but I needed to remove the 1” open spacer from the rpm intake and it now hesitates off the line. Would removing the spacer cause this and any suggestions for a cure?
Jon

11
Private Classifieds / Petronix Digital Hp box (New)
« on: May 30, 2021, 01:19:17 PM »
Petronix HP digital box $232@ Summit $175 plus shipping from Nj
3 step digital rev limiter
adjustable start restart
rpm trigger output
Jon

12
FE Technical Forum / 3G top mounted Alt
« on: November 26, 2020, 07:40:35 AM »
I want to swap alt and use a 3g single pulley alt with factory brackets...is it the sm or lg case unit that will work?
Jon

13
FE Technical Forum / 6an ptfe fuel line big enough?
« on: October 07, 2020, 11:51:30 AM »
my tank has a 3/8 pick up and the motor is around 500 hp ... is 6an ptfe big enough? it measures .32
which isn’t 3/8...
Jon

14
Private Classifieds / Free Johns 9” Rear
« on: August 10, 2020, 04:23:11 PM »
Came out of a Cobra, 49” wide  Large bearing ....1 tube rewelded with a bar....set up for triangulated 4 link.
MUST pick up in Englishtown, NJ
Jon

15
FE Technical Forum / 2500 rpm stall
« on: July 26, 2020, 06:25:07 AM »
can someone explain what this means? I want to put a C6 or C4 in my car and this converter was recommended. How is it different then the stock converter?
Does TCI make a good transmission?
Jon

Pages: [1] 2 3 4