Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - wayne

Pages: [1] 2 3
1
Private Classifieds / distributor parts wanted
« on: December 22, 2021, 11:09:44 AM »
Wanted    Dual point breaker plate out of any ford with a dual point and vacuum advance

2
Private Classifieds / Fe cams on sale
« on: November 03, 2021, 04:08:38 PM »
Crower has several  fe cams on clearance for $72 dollars

3
FE Technical Forum / Ray Paquet
« on: September 03, 2021, 10:16:55 AM »
Mr Paquet wins ss/a at indy with a real thunder bolt l think its number 30 class wins sure makes hemi and rat look bad. He sure knows how to build a fe.

5
FE Technical Forum / Dragway 42 shootlng ?
« on: June 15, 2021, 10:36:43 AM »
Was told their was a shooting at dragway 42 one dead is the track open for the ford race ?

6
FE Technical Forum / Bumper pistons
« on: May 09, 2021, 03:13:06 PM »
Has anyone milled 0.100 off the 63-64 bumper pistons and used a 428 crank i think i read about this years ago

7
Private Classifieds / valve springs
« on: November 24, 2020, 02:46:07 PM »
New edelbrock springs part number 5821 for edelbrock heads and a hyd roller cam 125.00 shipped.pm me if needed Wayne.

8
Private Classifieds / Ford Factory 3x2 Intake Setup
« on: November 13, 2020, 07:45:42 PM »
Complete setup, repop air cleaner and linkage. One thermostat hole is 3/8 instead of 5/16 but works good. Setup comes with a new thermostat housing. Setup is being sold as is, asking $1500.00 plus shipping. Local pickup is fine in southern lower Michigan. If you have any questions please pm me.
https://drive.google.com/drive/folders/1rsqvnrj6J1mM05SYpUEngbwXHhTQIpmt  sold

9
FE Technical Forum / crane cams
« on: September 30, 2020, 08:44:31 AM »
I think Edelbrock is going to close crane down if you need anything from them like rocker arm adj screws.

10
FE Technical Forum / Valve job
« on: August 01, 2020, 01:42:13 PM »
Do they still use torque plates on the heads when seats are ground.

11
FE Technical Forum / nrmra-nmca
« on: June 04, 2020, 01:19:19 PM »
Nmra-nmca will be at martin us131 end of aug not many fe but some of the worlds fast fords will be.

12
FE Technical Forum / Thank you
« on: May 25, 2020, 02:12:45 PM »
Thank you all Veterans we owe you a lot.

13
FE Technical Forum / main bearings
« on: May 25, 2020, 01:50:00 PM »
Crower has a good deal on 351c main bearings can be made to work in a fe tang is on other side.Go to clearance they are Acl.010 under for 10.00 bucks a set Jay i am not selling not sure where to put this post.

14
FE Technical Forum / Jet c 6
« on: March 23, 2020, 09:35:31 AM »
Did ford have have trouble why did they use the cast iron tail housing on cj and a pi. I have a c6 but not jet will it brake.





15
FE Technical Forum / fe oil galleys
« on: October 02, 2019, 05:19:46 PM »
When i went to do the oil galleys they were all done the oil pump to block was still small this is a service block with a cx in back.Did ford open them later in production the local ford dealer did this engine back in the 74 or 75 i am sure they did not do it.Its the first one i have seen.

Pages: [1] 2 3