1
FE Technical Forum / Re: FE bellhousing needed - QuickTime info
« on: August 13, 2022, 05:29:53 AM »
Just used a new quicktime in my car, no fitment issues whatsoever.
Dedicated to Building and Racing the Ford FE Engine
News:
SMF - Just Installed!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
FE Engine Dyno Results / Re: Lykins Motorsports 427 High Riser
« on: July 12, 2022, 01:33:19 PM »[/quote]
Any specs on that one as an NHRA stocker vs a Ford delivered version?
[/quote]
Filled block, thin rings, bbc rod journals, 20+ more duration, better valve springs, valve job, .013+ stroke, compression is just a tad over 15, 3 step headers......
3
FE Technical Forum / Re: Cam Thrust Plate Thickness
« on: July 07, 2022, 04:45:29 PM »
I bought a POP roller bearing setup, and the plate was machined already to accept the bearings, still needed .004 taken off...
4
FE Technical Forum / Re: Distributor's
« on: July 07, 2022, 04:40:36 PM »
I picked up a reman duraspark, and locked out the timing. Went to 7200 rpm on the dyno without a hitch.
5
FE Engine Dyno Results / Re: Lykins Motorsports 427 High Riser
« on: July 07, 2022, 06:54:37 AM »
Well, dynod my Nhra stocker blueprinted high riser. Untouched ports in the heads and intake support power well in into the 600s.....solid flat tappet cam with .524 lift.
6
FE Technical Forum / Re: Bottom End Capabilities
« on: April 26, 2022, 07:57:23 AM »I can guarantee you, Pond does not turn that HR in that range.
Agree.
7
Non-FE Discussion Forum / Re: Has anyone worked with the Pond High Risers yet?
« on: February 20, 2022, 12:14:29 PM »For Stock class is there a rated power bump with the Pond heads?
5hp
8
Vendor Classifieds / Re: NEW ALUMINUM HIGH RISER HEADS AND INTAKE!!!!
« on: January 06, 2022, 06:51:09 PM »
Has anyone laid eyes on these yet??
9
FE Engine Dyno Results / Re: Lykins Motorsports 427 High Riser
« on: January 06, 2022, 05:25:36 PM »
Which cam Brunson?
10
FE Engine Dyno Results / Re: Lykins Motorsports 427 High Riser
« on: January 06, 2022, 07:30:58 AM »
Nice build!
Do you think the factory 2x4 and carbs would yield more power?
Do you think the factory 2x4 and carbs would yield more power?
11
Private Classifieds / Reproduction High Riser Fuel Log
« on: November 04, 2021, 05:30:24 AM »
Brand new, never used.
$100
Located in NJ
$100
Located in NJ
12
FE Technical Forum / Re: Wide Band A/F ratio gauge ?s
« on: September 27, 2021, 08:26:34 AM »
You could look into the Daytona Sensors Wego unit. You can add that to RPM's DL10 datalogger and have evrything on one unit. Much cheaper than a racepak
13
FE Technical Forum / Re: alternator bracket
« on: September 27, 2021, 08:21:54 AM »
What is the lightest alternator available for the FE?
14
Private Classifieds / Re: ISO.. one 427 high riser head C4AE-F
« on: August 30, 2021, 11:40:49 AM »
Get on facebook and contact David Dove
15
Private Classifieds / Re: 9" Yukon 3.25 carrier bolt thru center section Aluminum
« on: August 30, 2021, 11:39:15 AM »
Sorry, should have updated, SOLD