Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 447 Stroker

Pages: [1] 2
1
FE Technical Forum / Re: 390 shakes at 1000 rpm – 1500 rpm – 2000 rpm, runs smoothly at 3000-3500 rpm.
« on: January 28, 2021, 11:16:45 AM »
Harmonic signature in tire? ( I build tires for a living ) It could be as simple as radial force variation in the tire, which is basically the roundness of a tire and the different stiffness the joints create.

2
FE Technical Forum / Re: Guess the horsepower game, 1961 Ford 390
« on: January 05, 2021, 11:15:02 AM »
336

3
FE Technical Forum / Re: 482 going on pump. Guess the HP version 2.0, prize to winner.
« on: March 23, 2020, 11:09:24 AM »
605

4
Private Classifieds / Re: Getting rid of some stuff
« on: January 29, 2020, 08:54:20 AM »
Yessir. Thank you.

5
Private Classifieds / Re: 428 PRW Sheet Metal Valve Covers
« on: January 28, 2020, 09:06:01 AM »
PM sent

6
Private Classifieds / Re: Dana 44 3.54 Limited Slip / Locker for F100
« on: December 04, 2019, 11:19:03 AM »
What part of Atlanta?

7
FE Technical Forum / Re: Chatter lately about rocker shim plates?
« on: November 26, 2019, 08:32:18 AM »
Gah, Needed a good set of shims about 3 months ago.  :'(

8
FE Technical Forum / Re: Another guess the horsepower to throw in the mix......
« on: November 06, 2019, 10:49:18 AM »
196/213

9
FE Technical Forum / Re: The next guess the horsepower game.....
« on: October 21, 2019, 07:34:16 AM »
410

10
FE Technical Forum / Re: EMC report
« on: October 04, 2019, 12:47:28 PM »
Someone mentioned it earlier, but I am curious about the center cap as well.

11
FE Engine Dyno Results / Re: All iron 68.5 CJ 461 inch 515 HP/530 TQ pump gas and power brake friendly
« on: September 04, 2019, 12:51:01 PM »
Thanks Joe!

12
FE Engine Dyno Results / Re: All iron 68.5 CJ 461 inch 515 HP/530 TQ pump gas and power brake friendly
« on: September 04, 2019, 07:30:15 AM »
Ross,

Do you have a build thread? Asking because I am wondering what all modifications were needed to make the FE fit. Love the car!

Zach


13
FE Technical Forum / Re: Belts or serpentine
« on: August 27, 2019, 01:23:01 PM »
I mocked up my CVF serpentine the other week (waiting on heads) and absolutely love it. It was a little steep price wise, but as of now I'm happy I went in that direction. The picture is not the best.

14
Private Classifieds / Re: 15X7 wheel
« on: July 31, 2019, 02:03:30 PM »
I've got two you can have just pay shipping. I'm in SC. DM me.

15
Non-FE Discussion Forum / Re: New Members - Introduce Yourselves Here!
« on: July 30, 2019, 10:30:34 AM »
Hello,

My name is Zach. I'm from South Carolina. I'm 35 and very inexperienced. I've had a decent number of "old" cars but have not built one.

My project is a 1964 Galaxie rust bucket. It's a good 50 footer.

Just got the block back from the machine shop. Short block assembled thus far. Survival Stroker kit. Edelbrock stage II heads from Keith Craft to arrive later this week hopefully. I've learned a lot from the site thus far.

I've rebuilt the rear end. 3.70 gears. Changed springs to +1/stiff. Wish I would have went +2. Now working on the engine bay for the car itself.

Pages: [1] 2