1
FE Technical Forum / Re: Cammer Vacuum Question
« on: November 10, 2019, 07:48:34 AM »
Looking for actual numbers from running engines. Surely someone has hooked up a vacuum gauge to a Cammer.
Dedicated to Building and Racing the Ford FE Engine
News:
SMF - Just Installed!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
FE Technical Forum / Cammer Vacuum Question
« on: November 09, 2019, 09:26:28 AM »
I am building a Cammer and plan to use an early Ford C6 transmission but have no idea how much manifold vacuum to expect for the shift modulator. I want to avoid a manual shift valve body. Using Pond block and heads, 11:1 compression, Comp street lift cams, original single carb intake with Holley HP. What kind of vacuum numbers are you Cammer folks seeing out of similar builds? Phil
3
Private Classifieds / Re: Wanted: 427 SOHC stub cam
« on: May 09, 2019, 08:56:51 AM »
Finally found one.
4
Private Classifieds / Wanted: 427 SOHC stub cam
« on: May 05, 2019, 08:16:09 AM »
Need help finding a 427 sohc stub cam. I will be using a new msd fe billet distributor and Crane steel gear. Thanks for any help or leads. Phil
5
Private Classifieds / Re: Wanted: 427 SOHC Single 4 Barrel Intake
« on: March 29, 2019, 09:13:07 AM »
I found one thanks to Jack Tindle. Now on with the build.
6
Private Classifieds / Re: Wanted: 427 SOHC Single 4 Barrel Intake
« on: March 21, 2019, 10:03:33 AM »
You are correct. I have already talked to Jay.
7
Private Classifieds / Wanted: 427 SOHC Single 4 Barrel Intake
« on: March 21, 2019, 09:41:38 AM »
Would like to buy a 427 sohc single 4 barrel intake for my current street build. Surely there is at least one out there just collecting dust. Could go with an aftermarket 2 x 4 setup, and they perform and look great, but prefer a single. Any leads would be greatly appreciated.
8
FE Technical Forum / 460 vs 427 motor mount location
« on: January 28, 2019, 08:37:19 AM »
Are the ford 460 and 427 motor mount locations the same? The length x width x height motor dimensions I have found online are very close. I have an aftermarket set up with shock tower delete for a 427 in a 67 Cougar but now considering switching to a 460 build instead.
9
Warning - Buyer Beware / Re: Post your negative feedback here
« on: January 27, 2019, 11:32:32 AM »
Bill Coon Steals Deposit
Bill Coon stole my $3000.00 deposit for a set of 427 SOHC (Cammer) heads. After months of excuses I had to cancel the order but he won't return the deposit even though I have an invoice and cancelled check. I have since learned this is a common business by Coon especially if you are located long distances from his shop in Romulus Michigan and the interstate costs to sue him. As a small builder in the Phoenix area I have many many contacts and will be notifying every Cammer vendor, engine builder, magazine editor, major car auction and show promoter I can find. All should be concerned this guy is killing interest in the Cammer.
Bill Coon stole my $3000.00 deposit for a set of 427 SOHC (Cammer) heads. After months of excuses I had to cancel the order but he won't return the deposit even though I have an invoice and cancelled check. I have since learned this is a common business by Coon especially if you are located long distances from his shop in Romulus Michigan and the interstate costs to sue him. As a small builder in the Phoenix area I have many many contacts and will be notifying every Cammer vendor, engine builder, magazine editor, major car auction and show promoter I can find. All should be concerned this guy is killing interest in the Cammer.
Pages: [1]