Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Fordman

Pages: [1] 2 3 ... 11
1
Private Classifieds / Re: Holman moody 2x4 MR intake
« on: March 28, 2024, 10:14:39 AM »
Bump*. Still for sale

2
FE Technical Forum / Re: Ford FE C7SF-12127-A distributor application?
« on: March 03, 2024, 10:10:29 AM »
Thank you Sir. Very appreciated!.👍

3
FE Technical Forum / Ford FE C7SF-12127-A distributor application?
« on: March 02, 2024, 11:01:12 PM »
Can anyone here tell me what a C7SF-12127-A distributor was originally for?. Thanks

4
Private Classifieds / Re: 67 Mustang Fastback
« on: February 23, 2024, 07:44:14 PM »
HWOODS is correct. IF you have a title, the dynacorn body is more affordable than rebuilding a rotten car. I restore classics and customs for a living. Inch by inch sounds great to the wallet at first but at the finish line.....not so much. Entirely JMO( from 25+ years experience)

5
Private Classifieds / Re: Wanted trick flow heads
« on: February 23, 2024, 07:40:36 PM »
There are several sets assembled and bare available on eBay. Just an FYI

6
FE Technical Forum / Re: Trickflow heads - gone for good?
« on: February 23, 2024, 06:07:11 PM »
There are several sets left on eBay, both assembled and bare. It's not like there are NONE left out there. Just saying....

7
Private Classifieds / Re: Ford FE Chet Herbert Solid roller camshaft
« on: February 04, 2024, 11:33:00 AM »
I have responded to your message twice with no reply. FYI

8
The loom reel says part# 16- P-C-7 100ft, loom is half full or more. Date code on the wire itself it 2-Q-66. $200 obo

9
Private Classifieds / Re: Wanted- mirror "105" block only
« on: February 01, 2024, 12:17:41 PM »
I have a couple std bore 105 blocks. Where are you?. Shipping could be prohibitive.

10
Private Classifieds / Re: NOS 390gt/428cj camshaft
« on: February 01, 2024, 12:15:19 PM »
New old stock=NOS
I NEVER said it was ford, I said it was a new, never used camshaft that is ground with 390gt/428cj valve timing events. Where is the confusion?.

11
Private Classifieds / NOS 390gt/428cj camshaft
« on: January 30, 2024, 12:48:18 PM »
This is a regrind from Colt Cams in Vancouver,BC. Stock specs new, never installed.$100

12
Private Classifieds / 66-69 fairlane Torino FE engine/ trans mounts
« on: January 30, 2024, 10:11:27 AM »
I have a set of FE frame/engine mounts for 66-69 Torino/fairlane, include rubber insulators $250
C6/4spd FE transmission cross member $150
#6113 hooker headers, good used $350***SOLD***
I also have rust free doors for 68/69 Torino/fairlane. Prefer pick up( south central BC/north central WA state. $200 each

13
Private Classifieds / Ford FE Chet Herbert Solid roller camshaft **SOLD**
« on: January 29, 2024, 02:30:06 PM »
Chet Herbert Solid roller camshaft part#GR262 260/270@.050, .705/.705 lift. Brand new never installed, can make a combo deal with the lunati sold roller lifters I also have listed. Asking $350 or reasonable offer..**SOLD**
Thanks!

14
Private Classifieds / Re: 428cj crankshaft std/std and 428cj rods
« on: January 29, 2024, 12:02:57 PM »
Crankshaft casting is 1U. Thanks

15
DR4-4
Clutch less, no downshift sliders. $3500 with clutch system I appreciate the interest but have two buyers already. If all else falls through I will let you know.Thank you

Pages: [1] 2 3 ... 11