Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Arizona ‘58Mercury

Pages: [1] 2
1
Vendor Classifieds / Re: More Lykins Motorsports non-adjustable roller rockers are on the way....
« on: January 04, 2020, 05:49:16 PM »
How are these performing?  Any feedback on them?

2
Vendor Classifieds / Re: Trying to judge interest in a new product....
« on: December 02, 2019, 09:42:42 PM »
At that price might as well buy a set of each... they just in case factor. 

3
Vendor Classifieds / Re: More Lykins Motorsports non-adjustable roller rockers are on the way....
« on: August 14, 2019, 01:42:01 PM »
I got my cam and lifters through you, I’ll be in touch on these as well.  Thank you

4
Vendor Classifieds / Re: More Lykins Motorsports non-adjustable roller rockers are on the way....
« on: August 14, 2019, 01:03:29 PM »
Yes, I miss read what you put above.

5
Vendor Classifieds / Re: More Lykins Motorsports non-adjustable roller rockers are on the way....
« on: August 10, 2019, 08:06:27 PM »
So what’s it run for the whole set up?  Rockers, shafts and pop ups

6
Vendor Classifieds / Re: NEW ALUMINUM HIGH RISER HEADS AND INTAKE!!!!
« on: March 08, 2019, 07:11:06 PM »
Will be watching for this!!!   Not putting my name on a list till I see information and prices however.

7
FE Technical Forum / Re: Valve Stem Wear Signature
« on: January 01, 2019, 09:05:31 PM »
On a hydraulic cam, you measure for pushrod length at zero lash/preload, then add the amount of preload that the manufacturer recommends to the length of the pushrod.  On most FE hydraulic setups, I run .050-.060” of preload.  Short travel lifters are another animal.
[/quote]


Okay Great!!  Thanks Brent,  I will be reaching out about a set of those rockers later in the year too.

8
FE Technical Forum / Re: Valve Stem Wear Signature
« on: January 01, 2019, 01:31:56 PM »
Watched that video, super simple. On geometry.  1 question came to mind however and he didn’t address it. Maybe I’m over thinking it.  Was he seting that up for solid lifters?   I didn’t hear any mention when he was setting up the pushrod to get length about allowances for hydraulic lifter compression.  If running hydraulic lifters is there a standard amount added to account for them?   Thanks


9
Vendor Classifieds / Re: Lykins Motorsports Non-Adustable Roller Rocker Arms....
« on: December 08, 2018, 03:05:31 PM »
I will be in the market after the new year

10
Vendor Classifieds / Re: FE Power Cast Aluminum Valve Covers
« on: August 29, 2018, 10:36:53 PM »
Any pics of the ones going out?  Different variations or script. 

11
Vendor Classifieds / Re: FE Power Cast Aluminum Valve Covers
« on: July 31, 2018, 08:50:54 PM »
YES!!! So now gonna dig through emails and find that number!!! I got the email, wow that is a lot of options!!  Very cool.  Will be running on a mild 390 and thinking of vented.  Since I’m a newbie any advice on pros and cons.

Will get that filled out and too you soon

12
Vendor Classifieds / Re: FE Power Cast Aluminum Valve Covers
« on: May 03, 2018, 02:39:14 PM »
Nice!! That is good news, I think we all have our fingers crossed. 

13
FE Technical Forum / Re: Edelbrock F427 Intake Manifold
« on: February 06, 2018, 11:43:54 PM »
Yeah I tried putting a pic on here from my phone but they won’t upload. 

14
FE Technical Forum / Edelbrock F427 Intake Manifold
« on: February 06, 2018, 09:50:16 PM »
Picked up this intake last week.  I know it’s older but all in all pretty good shape on all matting surfaces.  Only question is on a few of the corners of the pushrods passages they are clearances and not sure if from damage or not.  Can post a pic. Will it affect operation, if so options?

15
FE Technical Forum / Re: Pushrods
« on: February 05, 2018, 01:54:55 PM »
Sounds good, so the directions are measure from the cup of the lifter on base of the cam lobe up to the ball of the rocker assembly..  can anyone tell me what the factory wants the threads at for a start point?  Example: Like 2 threads showing out of the bottom of Adjuster.  Thanks

Pages: [1] 2