Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Saltshaker

Pages: [1] 2 3 ... 9
1
FE Technical Forum / what lb radiator cap w/expansion tank
« on: September 21, 2023, 09:33:49 AM »
what cap is used? can I use a 18lb cap?
Jon

2
FE Technical Forum / Re: popping exhaust
« on: August 08, 2022, 06:31:43 AM »
found the problem, replaced the distributor cap and rotor and it stopped.
thnx for all the suggestions
Jon

3
FE Technical Forum / popping exhaust
« on: August 07, 2022, 08:22:39 AM »
I have a random popping in my exhaust on the right side. This is in a 427 Cobra with side pipes , the pop is random and happens while driving or idling not while accelerating or the decelerating. I’ve tightened all the bolts on the headers and the slip on side pipes have bolts holding them together any suggestions I don’t see any strike marks from the exhaust.
Jon

4
FE Technical Forum / V Belt tensioner for a FE
« on: July 18, 2022, 08:39:22 PM »
is there a V Belt tensioner for a FE ?
Jon

5
FE Technical Forum / Re: return line to tank
« on: March 18, 2022, 05:26:20 PM »
checked the fuel lines and I hade the line to the carb running between the dist and the expansion tank
will reroute that tomorrow
thanks, Jon

6
FE Technical Forum / return line to tank
« on: March 18, 2022, 02:51:39 PM »
Warm here today and I’m have a problem with fuel boiling. Will a return line solve the problem? Does it need a by pass regulator or is there another way?
Jon

7
FE Technical Forum / Drain hose on expansion tank
« on: March 16, 2022, 08:55:38 PM »
Where does the drain hose go? Does the hose drain to the ground, back to the radiator or to a recovery tank?
Jon

8
FE Technical Forum / Re: the right stuff or ultra grey seal china wall
« on: December 27, 2021, 11:17:37 AM »
Jay, ty and Happy Holidays

9
FE Technical Forum / Re: the right stuff or ultra grey seal china wall
« on: December 27, 2021, 07:23:54 AM »
Jay, do you also use this around the water jackets on both sides?
Jon

10
FE Technical Forum / the right stuff or ultra grey seal china wall
« on: December 26, 2021, 03:42:28 PM »
replacing intake gaskets, oil leak back of the china wall. it was originality sealed with the right stuff but now it’s leaking. What have you had the best results with?
Jon

11
Non-FE Discussion Forum / Speedmaster 8 Stack
« on: November 28, 2021, 01:13:08 PM »
Anyone using this system? Is the gas mileage better then running Webers?
Jon

12
FE Technical Forum / Re: Intake leaking oil back of motor
« on: November 21, 2021, 02:47:30 PM »
Thnx,I’m going to give it a try… can’t hurt

13
FE Technical Forum / Re: Intake leaking oil back of motor
« on: November 21, 2021, 08:35:37 AM »
my leak is in the center of the block, I could easily trim or remove the rtv in that area. If I cleaned it with brake cleaner I’m sill not sure if you can apply the right stuff over existing the right stuff and get it to seal.
Jon

14
FE Technical Forum / Intake leaking oil back of motor
« on: November 20, 2021, 03:58:47 PM »
It is leaking at the back where the intake meets the block. Is there another way to fix it without pulling the intake?
I use “the right stuff “ to seal it
Jon

15
Private Classifieds / Re: 3/8 steel header flanges
« on: November 09, 2021, 05:43:49 PM »
jonk5152@yahoo.com
send me your email and I can send you the tracking number
jon

Pages: [1] 2 3 ... 9