Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - hbstang

Pages: [1] 2 3 ... 17
1
Non-FE Discussion Forum / Re: full spool
« on: March 12, 2024, 11:16:33 PM »
if you are going to street drive mostley,i would run the true trac geared posi.they are pretty strong and work like a spool in a straight line,and allow easy turns.not cheap though!

2
Non-FE Discussion Forum / Re: Calliope Engine Project
« on: March 12, 2024, 03:29:44 PM »
AMAZING WORK JAY! so are these 3 valve or 4 valve heads?

3
Member Projects / Re: Shelby stocker
« on: March 02, 2024, 04:52:37 PM »
( I get a bit jealous reading about everyone's projects while mine sits idle. I just can't seem to find the time to get much done.
 Well my 10yr project made a little progress, I got the new 9" rear in the car. I had everything measured for a tight tire fit (I got good suggestions from Afret) but as fate would have it the axle housing came back 1" narrower than planned when the housing ends were changed. I think everything will work out with a 3/8" spacer. I haven't run spacers on a drag car before, anyone with a comment on running them or not?)


10 years ago you started this thread,on a 10 year project.great job on getting it done!most people would have sold it off! car is really nice and i would like to see it run.where do you plan to run it?

4
FE Technical Forum / Re: Valve stem groove
« on: March 01, 2024, 03:08:12 PM »
i would replace the valaves myself as it should not do that in low miles.imho.

5
Private Classifieds / Re: 67 Mustang Fastback
« on: February 24, 2024, 02:21:45 PM »
maybe woody the op can chime in and be more specific for what he wants?are you looking for an origianl 67 s code fastback to restore or hot rod?

6
Private Classifieds / Re: 67 Mustang Fastback
« on: February 23, 2024, 02:36:54 PM »
pics? trades?with custom built engines running $25k thats a deal

8
FE Technical Forum / Re: Crower HIPPO lifters
« on: February 10, 2024, 08:31:54 PM »
those are great lifters,but 600 1/4 mile passes ! must be equal to 5,000 street miles is my guess.you may want to check with crower and see what they want to rebulid them.just my 2cents.i was told they would do that.

9
are these parts still available ?yes if ad is up still for sale

head bolts sold to ditzler

10
FE Technical Forum / Re: Fairlane at Sickweek
« on: February 04, 2024, 04:06:17 PM »
i seen your car on a video,that expains why i didnt see it later.tough luck on that.seems that track was super sticky so any week link would fail.
whats your combo on the car?

11
FE Technical Forum / Re: 427 Tunnel Port Video
« on: February 04, 2024, 12:11:14 PM »
good video thanks.it makes sense why the high riser was developed to increase port volume and flow with a taller port not wider.theres always a compromise some where using conventional head parameters.

13
Private Classifieds / Re: 65-73 Mustang Cal-Trac traction bars
« on: January 20, 2024, 06:06:43 PM »
nice deal thanks.

14
Private Classifieds / Re: 67 Mustang Fastback
« on: January 19, 2024, 06:19:04 PM »
whats your budget on this?are you going to restore it?

15
Private Classifieds / Re: 65-73 Mustang Cal-Trac traction bars
« on: January 09, 2024, 11:39:43 PM »
pm sent

Pages: [1] 2 3 ... 17