1
Private Classifieds / Re: 445 rotating assembly & block
« on: March 30, 2022, 06:39:34 AM »
Yep. Feel free to message me if you are interested.
Thanks,
-G
Thanks,
-G
Dedicated to Building and Racing the Ford FE Engine
News:
SMF - Just Installed!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Private Classifieds / Re: 445 rotating assembly & block
« on: March 26, 2022, 05:12:35 PM »
I'm in Holland. 10 minutes from East Aurora, 25 or so from Buffalo.
3
Private Classifieds / Sold 445 rotating assembly & block
« on: March 25, 2022, 07:23:11 AM »
Hey All,
I am selling a 445 stroker kit from Survival. 4.08" by 4.25", balanced I beam rods and dished pistons. Spec sheet in pics below. NIB except for crank test fit & 2 in the holes.
Block (2 bolt motor mount out of a Mercury) has been hot tanked, bored & square decked. Oiling system has not been modified. Just bit off more than I can chew with this one and I hate to see it sit.
Asking $1800.00 for the kit.
Asking $450.00 for the block.
Please message me for shipping, pickup, delivery from Western NY.
Thanks for looking,
-G
I am selling a 445 stroker kit from Survival. 4.08" by 4.25", balanced I beam rods and dished pistons. Spec sheet in pics below. NIB except for crank test fit & 2 in the holes.
Block (2 bolt motor mount out of a Mercury) has been hot tanked, bored & square decked. Oiling system has not been modified. Just bit off more than I can chew with this one and I hate to see it sit.
Asking $1800.00 for the kit.
Asking $450.00 for the block.
Please message me for shipping, pickup, delivery from Western NY.
Thanks for looking,
-G
4
Member Projects / 445 in a 67 Fastback
« on: November 01, 2021, 01:55:33 PM »
Finally getting started on a 445 stroker for my 67 Mustang.
Picked up an older (2 bolt motor mount) Mercury 390 & c6 at Carlisle a couple years back. Had the usual inspection/machine work done to the block and after a clean bill of health, began collecting parts.
I'm not new to the world but I am new to the forum. I'll need plenty of advice along the way. Seems I am in the right place and in good hands though. Thanks in advance and thanks for looking.
State of the car so far:
Survivor level sheet metal & interior.
New MII coilover IFS and various unibody, floor pan & torque box work
Street/strip build C6 & 3.70 rear (9")
26" tires
Power steering
Manual disks
Project goals:
Ornery street motor in a driver that will carry me along swift n' true all 33 miles of my back road commute.
10.33:1 compression with what I have so far.
Waiting for 72cc Performer RPM heads & Performer RMP intake. I'll reach out to the tech section for help on picking a pump gas friendly cam.
And here's hoping the pic went through.
-G
Picked up an older (2 bolt motor mount) Mercury 390 & c6 at Carlisle a couple years back. Had the usual inspection/machine work done to the block and after a clean bill of health, began collecting parts.
I'm not new to the world but I am new to the forum. I'll need plenty of advice along the way. Seems I am in the right place and in good hands though. Thanks in advance and thanks for looking.
State of the car so far:
Survivor level sheet metal & interior.
New MII coilover IFS and various unibody, floor pan & torque box work
Street/strip build C6 & 3.70 rear (9")
26" tires
Power steering
Manual disks
Project goals:
Ornery street motor in a driver that will carry me along swift n' true all 33 miles of my back road commute.
10.33:1 compression with what I have so far.
Waiting for 72cc Performer RPM heads & Performer RMP intake. I'll reach out to the tech section for help on picking a pump gas friendly cam.
And here's hoping the pic went through.
-G
5
Vendor Classifieds / Re: Four pair of TFS hydraulic roller assembled heads in stock....
« on: September 27, 2021, 12:11:33 PM »
I just sent you an email, Brent
GPtorch
GPtorch
6
Vendor Classifieds / Re: I have TFS heads in stock.....6.18.21....have another 6 heads in stock.
« on: June 30, 2021, 01:25:34 PM »
I believe I'll take a pair too. I'm sure you've covered specs elsewhere so I apologize. What size combustion chamber on your TFS? I am looking for a good Hy roller head to go with the pump gas friendly 445 dish piston stroker kit BR is cooking up for me now.
Shipping to 14080
Gus
Shipping to 14080
Gus
Pages: [1]