Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - cdale

Pages: [1] 2
1
Private Classifieds / Re: Harland Sharp bronze bushed Rockers
« on: June 15, 2026, 11:21:19 AM »
Sale pending

2
Private Classifieds / Harland Sharp bronze bushed Rockers
« on: June 14, 2026, 11:29:52 AM »
I have a set of Harland Sharp bronze bushed Rockers for sale 1.76. Ran for two summers under a hyd roller cam. Maybe 500 miles, 600$ +ride 716-861-2825 Chuck

3
Private Classifieds / Pst drive shaft
« on: April 09, 2026, 07:56:10 AM »
PST drive shaft for 63 galaxie 4sp set up for 28 spine 1330 yoke.  3 1/2" .083 wall Dom 300$ can bring to Muncie 716-861-2825

4
Private Classifieds / Parts For Sale!!!
« on: August 18, 2025, 04:35:48 PM »
will be a Bever Springs for FE Race and Reunion
call or text 716-861-2825

Slightly used Bullet HYD roller camshaft, comes with short travel comp lifters, custom push tubes, asking $600   
Specs:                     
                             Intake   Exhaust
Duration At .050       234.       240.
Gross Valve Lift:      .593       .588

PST drive shaft 28 spline 330 yoke, asking $275

Center council for 1963 Ford Galaxie 4 SD, asking $500

Heater box for 1963 Ford Galaxie $350

Update: camshaft and lifters are sold.

5
FE Technical Forum / Re: 63 ford galaxie axles
« on: June 26, 2025, 04:17:54 PM »
Thanks for all your advice, I called moser order everything with them and yes you can run 35 spline moser has a bearing for small ford 9" housing

6
FE Technical Forum / 63 ford galaxie axles
« on: June 22, 2025, 04:52:48 PM »
Ordering axles for a 63 galaxie stock 9" small bearing. What axle leath I would need going 35 spline. Thanks for any help

7
Private Classifieds / Re: wtb input shaft
« on: January 13, 2024, 10:12:37 PM »
found one thanks for all the help

8
Private Classifieds / Re: wtb input shaft
« on: December 05, 2023, 06:43:20 PM »
Thank you

9
Private Classifieds / wtb input shaft
« on: December 04, 2023, 04:40:30 PM »
WTB, LOOKING FOR A 1'3/8 INPUT FOR MY TOPLOADER CONVERSIOR

10
Private Classifieds / Re: '63 Galaxie complete grille, very nice used
« on: July 29, 2022, 10:38:48 AM »
No problem take care

11
Private Classifieds / Re: '63 Galaxie complete grille, very nice used
« on: July 28, 2022, 09:13:59 PM »
Any chance you plan on going to Beaver Springs in September? I know it might be a long shot, but up to you. I would be willing to meet you there if you are going.

12
Private Classifieds / Re: '63 Galaxie complete grille, very nice used
« on: July 26, 2022, 02:50:36 PM »
Okay, I'm about 5 hours out was hoping you were closer. any more 63 galaxie parts, what is the shipping on that

13
Private Classifieds / Re: '63 Galaxie complete grille, very nice used
« on: July 26, 2022, 08:57:46 AM »
just wondering if still available? where about in ohio are you. Im near buffalo ny thanks

14
FE Technical Forum / Re: fpa headers
« on: May 04, 2022, 04:43:42 PM »
I WAS ABLE TO USE MY STOCK 390 EQUALIZER BAR. THANKS

15
FE Technical Forum / fpa headers
« on: April 28, 2022, 08:20:40 AM »
I have a 63 galaxie with fpa headers 4 speed. I have the 353,390, clutch equalizer bar will that work with the headers or will i have to purchase the 427 equalizer bar. thanks for any help

Pages: [1] 2