Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Dubs1

Pages: [1] 2 3 ... 8
1
Vendor Classifieds / NEED MANUAL GEARED STEERING BOX FOR 1968 MUSTANG fb
« on: September 15, 2025, 09:43:27 AM »
DO any of you have a good  manual steering box  for a 1968 Mustang fb.

if so please advise cost and shipping fees

Dubs   at  ltduba@hotmail.com    or  (720)  839 3477

Many thanks

Dubs

2
Hi Guys

I need  a tranny speedometer gear for a 3:50 rear end in my Mustang

Who carries those items?

Dubs  in DEnver

3
FE Technical Forum / Re: RADIATOR HOSE FOR FE EDELBROCK WATER PUMP
« on: March 26, 2025, 04:13:43 PM »
PEGASUS  AUTO RACING  HAS A   2 INCH STEP UP TO A 2 1/4   PART NUMBER SR57.51.  THAT ONE IS  A SHORTER VERSION.

CALL THEIR 800# FOR DIFFERENT LENGTHS.

DUBS SENDS

4
the steering ger on my 68 FB  is shot and I have found a stock replacement but i need to know if it is the manual or pwr steering  MUSTANG STR BOX.
 
The part no. that is readable is C8ZB 35 S or5(not clearly readable) A,     date code 7A9,  four full turns lock to lock.  Is this the manual steering gear?

Pls advise

Dubs in Denver

5
FE Technical Forum / Re: RADIATOR HOSE FOR FE EDELBROCK WATER PUMP
« on: March 18, 2025, 07:15:40 PM »
THANK YOU EVERYONE   WHO RESPONDED.

THE GATES 206 IS ON A FFIENDS S CODE 390  THAT HE INSTALLED ABOUT 12 YEAERS AGO.  AND THE LETTERS /NUMBERS ON THE HOSE READ 206.

I WILL WORK THE HEATING AND SILIICONE IDEAS. 

6
FE Technical Forum / RADIATOR HOSE FOR FE EDELBROCK WATER PUMP
« on: March 17, 2025, 06:48:08 PM »
Hi guys

JAY. CAPT COBRA JET. QUESTION FOR YOU OR ANY OTHER BRAIN TRUST IN THAT AFTER INSTALLING THE EDELBROCK WATER PUMP ON MY 427, I AM STRUGGLEING TO FIND A LOWER RADIATOR HOSE  TO CONNECT THE PUMP TO THE RADIATOR.  A FRIEND HAD HIS INSTALLED 12 YEARS AGO AND HAD A GATES PART NUMBER 206 WHICH FIT FINE. NAPA AND OREILLY SAY ITS NO LONGER AVAILABLE. OD ON THE PUMP IS 2.25 AND OD ON THE RADIATOR IS 2.0.
IF YOU KNOW OF A HOSE AVAILABLE PLS PASS ON THE MAKE  AND PART NUMBER.
I SUPPOSE CHANGING THE RADIATOR OUTLET IS POSSIBLE BUT KINDA EXPENSIVE

THE MUSTAMG IN QUESTION IS AN S CODE 1969 FASTBACK. 

MANY THANKS

DUBS IN DENVER


7
Hi Guys

Im looking for  the inspection pan that goes underneath the bell housing on a FE block.  Do you have any available for sale?  pls advise

Larry  7208393477   ltduba@hotmail.com

8
Vendor Classifieds / Re: Craft Stage 3 Edelbrock Heads For Sale
« on: January 09, 2025, 11:29:46 AM »
Good Morning Capt

ON another note, do you have any of the inspection plates for  390/427 , the ones that go underneath the clutch and flywheel?

Pls advise 

Larry in Colorado

9
Private Classifieds / FE INSPECTION TRAY
« on: January 09, 2025, 11:25:20 AM »
Need to purchase  332-428 metal inspection tray  that covers the clutch and flywheel.

Please call or email Larry  if you have two available  720 8393477   ltduba@hotmail.com

thanks 

Larry


10
The specs are as foliows;

gross valve lift    INTAKE      EXHAUST          PART  3        33-000-11   SN  #   l  0199-16

                            .600          .622          GRIND #    FB  3316r     3317r

DURATION   
TAPPET LIFT .006  287           .293


VALVE TIMING       OPEN              CLOSE   
                   .050    INT  11    BTDC   45  ATDC

107.0    INTAKE CENTERLINE


DURATION   @   .050      INTAKE           EXHAUST
                                         236               242
LOBE LIFT                       .3470              .3600

LOBE SEPARETION    112.0

11
Private Classifieds / NEW HYDRALIC COMP CAMS HYDRAULIC ROLLER SET
« on: May 13, 2024, 10:53:09 AM »
FOR SALE

NEW NEVER USED SET OF COMP CAMS  FE  HYDRAULIC ROLLER SET.

ASKING $450/offer   plus shipping

Larry     ltduba@hotmail.com    (720) 839-3477


12
Non-FE Discussion Forum / Re: If anyone has contact for Dubs
« on: January 06, 2024, 12:16:02 PM »
Hi Drew

Thank you for the  heads up.  I have changed  my password  and block any  future  incursions

All the best

Dubs

13
Non-FE Discussion Forum / Re: Preferrred shipping company for Alum heads?
« on: December 17, 2023, 04:32:47 PM »
Hello Deandan

Many thanksfor the sage advice.  Will follow it fully plus a bit more body and ends

All the best

Larry

14
Non-FE Discussion Forum / Re: Preferrred shipping company for Alum heads?
« on: December 15, 2023, 10:11:09 AM »
THANK YOU GENE

15
Non-FE Discussion Forum / Preferrred shipping company for Alum heads?
« on: December 14, 2023, 01:00:53 PM »
Hi Guys

Does anyone have a preferred shipping freight company to send a pair of Aluminum  heads.

Pls advise

Many Thanks

Use either this forum or text  720 8393477

 

Pages: [1] 2 3 ... 8