1
FE Technical Forum / Re: Fe Specialties
« on: August 31, 2025, 03:48:53 PM »
Thank you for the information
Dedicated to Building and Racing the Ford FE Engine
News:
SMF - Just Installed!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
FE Technical Forum / Fe Specialties
« on: August 30, 2025, 11:52:43 PM »
Is Fe Specialties still open?
3
FE Technical Forum / Re: 428 cam section
« on: August 19, 2025, 06:33:46 PM »
Is there any aftermarket blocks being produced any more?
4
FE Technical Forum / Re: 428 cam section
« on: August 18, 2025, 05:25:18 AM »
Thank you Fryedaddy and Brent for input.
I will email you Brent.
I will email you Brent.
5
FE Technical Forum / Re: 428 cam section
« on: August 18, 2025, 03:26:57 AM »
After a day of research i come a conclusion that I need to improve the air flow and efficiency of the engine. Some port work and new rocker arms.
First I need to get the bottom end to handle the extra horsepower than work on the flow of the air.
Brent I would like to talk to you about of a plan of attack. To get me where I want to be with this engine.
Paul
First I need to get the bottom end to handle the extra horsepower than work on the flow of the air.
Brent I would like to talk to you about of a plan of attack. To get me where I want to be with this engine.
Paul
6
FE Technical Forum / 428 cam section
« on: August 17, 2025, 05:07:01 AM »
I would like to start gathering parts to up grade my 428 engine in a cobra replica. Little about the engine is bored 30 and running 10.5 compression. Cam spec HYD 310 cam lift 542 valve lift 270 Dur .221 050 Dur lobe center is 108.Heads are Survial FElony head matched port to a Edelbrock rpm manifold with a 750 Holley for carb. Stock adjustable rocker arms with new shaft and end stands. The bottom end is stock except the arp rod bolts was installed. Transmission is TKX and 3:31 rear gears. Dyno 473 horsepower and 501 toque.
My question if I up grade the rocker arms and cam would I gain more than 50 or more horsepower gain with these changes.
Paul
My question if I up grade the rocker arms and cam would I gain more than 50 or more horsepower gain with these changes.
Paul
7
FE Technical Forum / Re: Porting Heads
« on: December 02, 2023, 11:50:56 PM »
Thanks for the advice
8
FE Technical Forum / Re: Porting Heads
« on: December 02, 2023, 10:28:08 PM »
What cam would you recommend for a middle range rpm? This motor is in a cobra. Would like to increase torque . This what I am trying to achieve with this engine.
9
FE Technical Forum / Re: Porting Heads
« on: December 02, 2023, 05:01:42 PM »
Cam is
Cam lift .310
Valve lift .542
Dur 270
Dur .050 221
Lube center 108
Cam lift .310
Valve lift .542
Dur 270
Dur .050 221
Lube center 108
10
FE Technical Forum / Re: Porting Heads
« on: December 02, 2023, 04:31:00 PM »
428 block bore 30 over
Barry Motorsports heads matched to a elderbrock Rpm manifold. Compression 10.4. Stock Adjustable rocker arm
780 vacuum secondary carb.
Barry Motorsports heads matched to a elderbrock Rpm manifold. Compression 10.4. Stock Adjustable rocker arm
780 vacuum secondary carb.
11
FE Technical Forum / Re: Porting Heads
« on: December 02, 2023, 03:31:26 PM »
I am sorry.
Who does the best job on porting on heads and manifold?
Who does the best job on porting on heads and manifold?
12
FE Technical Forum / Porting Heads
« on: December 02, 2023, 12:43:15 PM »
I would to port my aluminum head and manifold to get a few more horsepower.
Pages: [1]