Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - FordEver

Pages: [1] 2 3 4
1
Non-FE Discussion Forum / Re: Muncie FERR hotels
« on: February 07, 2026, 12:31:59 PM »
Track is about 10 miles northeast of Muncie. We stayed near Ball State University, lots off motels/restaurants  lots off traffic but once out of that area fast drive to track. Long drive for you but hope to see you there.  All those 8 second FE, s and Cammers, neat event. 

2
FE Technical Forum / FERR Videos 2025 Muncie, In
« on: May 01, 2025, 08:35:39 AM »
https://www.youtube.com/@infraredloaf
My son Jason shot these videos, great event.

3
Non-FE Discussion Forum / Ford Racing CM-6731-FL1A Filter
« on: June 01, 2023, 08:27:53 AM »
Bought a case last year. Had 4 leak at top crimp. Installed Wix 51515R no leaks. Anyone else had problems ? Used the discontinued FL1AHP for years, no probems. Any one else had problems ?

4
FE Technical Forum / Re: 2021 Fast Fords at Dragway 42 Re-Cap
« on: June 23, 2021, 07:46:11 PM »
If possible, try not to schedule the same weekend as Hot Rod Reunion Bowling Green Ky. usually Fathers Day weekend. Thanks for putting this event together.

5
Drag Strip Results for FE Powered Vehicles / Kevin Czajkowski,s FE Fairlane Wins Badger Classic NSS
« on: June 21, 2021, 08:49:03 PM »
Kevin outlasted a tough field for the Win running on a 9.75 index at the Easu Clare Wi track.  Nice job Kevin. Check out the video.
https://youtu.be/xXOdllO8pzw

6
FE Technical Forum / Re: Drag Springs
« on: April 03, 2021, 07:56:29 PM »
Googled it, prices/availability all over the place this place usually has stuff
https://www.rockauto.com/en/parts/moog,8236,coil+spring,7512.
Recommend not cutting first , we put them in my sons stoch 289-4spd car, too high. Sometimes Moog stuff is too tall, and does not settle. Might be just right for your setup first try.
For comparison ,I have 8236 1/2 coil cut sits about stock/level with 28" front,  29" rear slick. Mine weights 3150 no driver, Glass fenders, bumpers ,hood, decklid, alum heads, intake, radiator, lexan windshield, plastic race seats, lightweight steel doors, no heater box ect.
I like to keep it about stock height so headers clear on/off trailer.
Good luck maybe see you at Glory Days Byron, say hi to your Dad, Bob

7
FE Technical Forum / Re: Drag Springs
« on: April 02, 2021, 11:35:36 AM »
I had Moroso 47160 no cuts with roller spring mount CalTrac 90-10, upper control arm limiter.
Spring bend out some as the roller did not resist.
It was too bouncy, hit the stop, dropped down+up a few times. inconsistent. Ride height about stock with 28" front runner.
Put Moog 8236 small block/6 cylinder with 1/2 coil cut, poly bushing  spring mount, CT 90-10 same height, spring not bent out.
Seems to lift/launch same with no bouncing, 60 ft more consistent.
Moog 8236 uncut  was one coil shorter than 47160, same diameter coil. Big block old spring bigger coil diameter but shorter.
Added one shock rubber bushing under the mount to move the shock down prevent over extending.
If you want to try the 47160 or roller mount let me know, Bob.
https://drive.google.com/file/d/1jTxmXuZR4L96trACngK91qslq3_0ftDx/view
https://www.moroso.com/pub/media/pdf/TrickSprings.pdf


8
FE Technical Forum / Re: Any FE friendly machine shops in Northern Illinois?
« on: April 02, 2021, 08:04:26 AM »
http://opelengineering.com/
Western Chicago burbs, did all machine work on my FE, good people, tell Ted Bob Mosher referred you.

 

9
Member Projects / Re: Putting A Little Pep In My 390's Step
« on: November 11, 2020, 08:51:16 AM »
We had a great time the last two weekends hanging out with you and Dad.  Good way to end the season. Quality / appearance /performance off the Fairlane is great.  Talk to you later, Bob

10
Member Projects / Byron time run 11/7
« on: November 09, 2020, 09:08:40 PM »
https://drive.google.com/file/d/1jTxmXuZR4L96trACngK91qslq3_0ftDx/view?usp=drive_web
Jason got one off our runs Saturday

11
FE Technical Forum / Re: I'm baffled! MSD distributor will not drop in?
« on: March 10, 2020, 07:37:26 AM »
All off the above possible plus , I had replaced that  push in oil plug with a threaded one, it stuck out too far, removed it ground it down, then dropped in.

12
Non-FE Discussion Forum / Re: FEs in the Finals at 2020 Winternationals.
« on: February 13, 2020, 08:44:24 AM »
https://www.facebook.com/nicksansom/videos/10157855973137086/UzpfSTExNzAyMDY1NTI6Vks6MTU0MTQyMjk4OTM0MjQ0OQ/
Good video, congrads to Robert making it to finals, Bob M

13
FE Technical Forum / Re: Tunnel Wedge 2x4 sideways Holleys linkgage
« on: January 21, 2020, 05:50:44 PM »
What Tunnel Ram kit ?  a 460, BBC, Cleveland, or ? I see no specific FE kit. Thanks, great picture,Bob

14
FE Technical Forum / Tunnel Wedge 2x4 sideways Holleys linkgage
« on: January 19, 2020, 05:54:25 PM »
What have you used for linkage ? Is their any FE specific available or is some adapting required. 
Using this adapter
https://www.jegs.com/i/Edelbrock/350/2694/10002/-1?gclid=EAIaIQobChMIiIPsrtOQ5wIVYpJbCh0gywVnEAQYASABEgJ8hfD_BwE

15
Non-FE Discussion Forum / Kenny Gresham Passing
« on: December 17, 2019, 08:36:25 PM »
Fellow NSS Racer/car builder passed Monday. He ran a 62 409 bubble top and couple  427 63 1/2, built several 55 Chevys and more. From the St. louis area, great guy, always a pleasure to be around, he will be greatly missed by family and the Racing community, Race on Kenny, Gods Speed.
https://www.irwinchapel.com/obituaries/Kenneth-J-Gresham?obId=9621124#/obituaryInfo

Pages: [1] 2 3 4