Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - MRadke

Pages: [1] 2 3 ... 10
1
FE Technical Forum / Re: Push rods for a fresh 445 build
« on: July 16, 2026, 12:48:02 PM »
Quote from: blykins on July 15, 2026, 08:22:23 AM
Need to measure.

You can go to Smith Brothers for push-sticks.  Get a good pushrod length checker that has the correct ends:  5/16" ball on lifter end and 3/8" cup on rocker end. 

Get your length(s), then call them and ask if they want an OAL measurement or bottom of cup measurement.  If BOC, put a ball bearing in the cup, measure the overall length, then subtract the diameter of the ball bearing.

Pay attention to where Harland Sharp wants the adjuster placement when you measure and make sure the cup on your length checker does not contact the rocker arm body at full lift.

Am I missing something?  Wouldn't you add the diameter of the ball bearing?

2
FE Technical Forum / Re: End of the Line for FE Power Cast Aluminum Products
« on: April 09, 2026, 11:56:27 AM »
Have you checked with Avalon Precision Metalsmiths in Markesan, WI?  They were just purchased by Sigma, but historically they have done smaller batch precision castings.

3
Member Projects / Re: Shock absorbers?
« on: December 25, 2025, 10:33:13 AM »
I used a set of Napa coilovers on my 66 Galaxie.  It made a world of difference.  Better tire clearance, ride quality and handling.  I still have the original springs, while i could have replaced them, that seems to be something of a crap shoot too.

Mike

4
Non-FE Discussion Forum / Re: Degree the cam on 2.8L Ford V6
« on: November 25, 2025, 03:23:01 PM »
How many people do you think have a 2.8 v6?  on an FE forum?

I had one in a 77 Pinto hatchback when I was 17, but I couldn't begin to tell you how to degree the cam on one other than it shouldn't be much different than any other engine.

I generally don't reply unless I have something worthwhile to add, with this possibly being an exception.

Mike

5
Non-FE Discussion Forum / Fatal Accident at Oklahoma drag race
« on: November 03, 2025, 05:27:50 PM »
https://www.firerescue1.com/fatal-incident/2-first-responders-volunteer-killed-at-okla-drag-racing-event?utm_source=delivra&utm_medium=email&utm_campaign=FR1-Daily-11-3-25&utm_id=9728444&dlv-emuid=61ebc4c4-564b-4bef-90d9-16c378bdfe6a&dlv-mlid=9728444


6
FE Technical Forum / Re: Who to contact about a running 427 to sohc conversion parts list?
« on: October 31, 2025, 03:28:43 PM »
Quote from: Jb427 on October 31, 2025, 11:06:34 AM
I am thinking hard about converting my 482 to a sohc the part that scares me is getting a parts list. Who should I try for a list of what I need I am not in the USA so that adds an extra layer of problems.

I'am thinking 20k and 12 months should be close to find all parts instock and buy them dose that sound in the ball park?

If I had the cash to build a SOHC, I think I would start out with a new block, rather than taking a stout engine apart.  If nothing else, you'll still be able to enjoy your car while you are finishing the new mill. 

As always, advice is worth what you pay for it.  It's easy to spend someone's money for them.

Mike

7
FE Engine Dyno Results / Re: 352 Daily Driver 438 hp/456 tq
« on: March 26, 2025, 01:49:05 PM »
Will the Kugles fit in a 66 Galaxie?  That's a very cool build.

8
Non-FE Discussion Forum / Re: Tom Posthuma - Farewell to a great FE guy
« on: November 04, 2024, 03:43:41 PM »
What a huge loss! I'll miss his posts and pictures.  RIP

9
Member Projects / Re: Carburetor madness by Drew
« on: September 28, 2024, 12:47:14 PM »
Drew was hit pretty hard with this last hurricane.  https://www.facebook.com/share/p/h57nbAX7xZEQPoiu/ 

10
Private Classifieds / Re: 77 peter pirsch 85ft aerial on 75 c900 chassis
« on: April 28, 2024, 06:32:53 PM »
Hopefully this works, only a picture but better than nothing

11
Private Classifieds / 77 peter pirsch 85ft aerial on 75 c900 chassis
« on: April 28, 2024, 06:26:37 PM »
I know this isn't FE, but it is a very cool old Ford. I had the honor of driving this one last time to take it to auction.
 This will be for sale on the R&M motors retirement auction on Monday 4/28
https://www.facebook.com/share/v/h16F4VF9twG4KGJW/?mibextid=oFDknk

It has a 531superduty with a 5 spd transmission

I have a video of the truck running, but someone handier at these things than me would have to do it.

12
Non-FE Discussion Forum / Re: Side mirrors for Galaxie
« on: April 04, 2024, 01:19:16 PM »
I actually want to add one, even though it didn't come with one.  The garage stall that it resides in is uncomfortably narrow and a passenger mirror would help in backing out without rearranging the sheet metal.  My driver's side mirror is rectangular and I have to readjust it every time I close the door.

13
Non-FE Discussion Forum / Re: Side mirrors for Galaxie
« on: April 01, 2024, 01:17:13 PM »
Mine is loose at the ball adjustment at the mirror.  The bigger issue is that I don't have a mirror for the passenger side.

14
Non-FE Discussion Forum / Side mirrors for Galaxie
« on: March 31, 2024, 09:27:43 AM »
Are the reproduction rectangular rearview side mirrors decent quality, or should I be looking for an original?  The diver's side mirror on my 66 is getting sloppy and I'd like to add a mirror to the passenger side.

Thanks and Happy Easter

15
Non-FE Discussion Forum / Re: Plowing the highway
« on: December 23, 2023, 01:29:40 PM »
Snow removal is just another one of those things that we take for granted these day.  Thanks for posting a picture of your 4 horse town.

Merry Christmas
Mike

Pages: [1] 2 3 ... 10