Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - machyoung

Pages: [1] 2 3 ... 6
1
FE Technical Forum / Re: HS rockers
« on: February 02, 2026, 08:07:34 AM »
POP has shims (usually sends them along with either their stands or spacers, can't remember. .015, .030, and .060. Mix and match till you get the required spacing. Brent has a "how to" video that's pretty explanatory.

2
Private Classifieds / Re: Dipstick and tube
« on: November 30, 2025, 07:27:05 AM »
I've got one. Stand by and I'll shoot you a pic and get the numbers off of it.

3
Non-FE Discussion Forum / Re: A tour of Jon Kaase’s operation
« on: September 05, 2025, 07:18:48 AM »
Super impressed. Thanks for posting!

4
Private Classifieds / Re: FE Engine Parts - new and used
« on: August 05, 2025, 08:01:10 PM »
I will take the PI intake if not spoken for.

5
Member Projects / Re: Winter project pretty much finished
« on: February 25, 2025, 09:15:59 PM »
Beauty!

6
FE Technical Forum / Re: Fairlane header options
« on: October 26, 2024, 07:20:06 AM »
I have FPA's on my 68 w/ FE and Borgeson. I did run the lines up  and over the shock tower however no issues w/ the steering box. Like them a lot.

7
Private Classifieds / Re: Wanted: crank oil slinger
« on: July 14, 2024, 07:21:52 PM »
Send me your address and $5 for shipping and I'll send you one. Unless, you're in SoCal.

8
Private Classifieds / Re: Need 390 double crank pulley
« on: December 19, 2023, 07:12:56 PM »
mustangtek.com is a great resource to assist in identifying the pulley that you are looking for.

9
Non-FE Discussion Forum / Re: it happens
« on: December 04, 2023, 09:27:35 PM »
My kryptonite is anti-seize. I put it on one bolt and I have it on everything... That's just the way it is...

10
Non-FE Discussion Forum / Re: it happens
« on: November 30, 2023, 08:36:16 AM »
The arthur cream that I use says to wash your hands after application. Seems counter-productive to me...

11
Non-FE Discussion Forum / Re: Turn up the speakers
« on: November 28, 2023, 07:43:46 AM »
Quote from: TurboChris on November 28, 2023, 12:37:03 AM
Personally I'd take the sound of my old H2 750's with Denco chambers over a norton anyday.  ;D

Along with the smell of Castrol "R". Yep!

12
Non-FE Discussion Forum / Re: Burnout and tire hopping remedy?
« on: August 29, 2023, 05:21:07 PM »
Quote from: MeanGene on August 29, 2023, 02:42:32 PM
Can you run a tight pinion snubber with Cal-tracs? I used to have one that was built up about 3 inches on my Galaxie, ala the old Mopar setups, and it worked pretty well. The Gal has 7 leaves (up from the 406 6 leaves) and clamps

Didn't the higher performance Mopars also have a longer supporting leaf or additional leaf on the pass side

13
Non-FE Discussion Forum / Re: Cougar steering wheel
« on: August 13, 2023, 02:31:56 PM »
I've got a blue hanging around if you're in need. Let me know...

14
Non-FE Discussion Forum / Starter Assistance
« on: August 13, 2023, 02:22:03 PM »
Good day all. Seem to have gotten my starter parts out of order. Can anyone assist?

While replacing the Bendix drive on my starter I have come-up w/ an extra washer (found in rag that I was using to clean with). It's a very thin, .005 approx steel washer. Can anyone tell me it it goes on the armature shaft before the drive, after the drive or after the C-clip? None of my manuals are any help. The internet is a crap shoot...

Thanks all!

15
Member Projects / Re: Shelby stocker
« on: June 29, 2023, 04:26:28 PM »
Looking Fantastic Mike!

Pages: [1] 2 3 ... 6