Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - nitro98red

Pages: [1] 2
1
Private Classifieds / Pond 2x4 SOHC Manifold SOLD
« on: December 12, 2022, 11:22:38 AM »
Hi, Have a Pond Manifold that was used to run the engine on a engine stand then we switched over to the BORLA fuel injection set up. Has about 5 hours run time on it. Unmolested.
1650 USD shipped anywhere in the lower 48 and Canada.
Thanks Shane
403-846-8852


2
Private Classifieds / SOLD NIB 427 sohc edelbrock water pump
« on: March 24, 2019, 10:38:32 AM »
427 sohc edelbrock water pump modified by the late Jim Barrillaeo. Went with a electric pump so this is surplus to my needs. Never used. Bolted on the motor for mock up.
450 usd shipped lower 48 and Canada.
sleepyj5@live.com
Work in out of the country apologize head of time for any relate replies.


3
Member Projects / Re: SOHC mustang convertible longest project ever
« on: November 26, 2018, 09:00:16 AM »
Just got home from work. Going to the shop tomorrow. Alternator and AC compressor are to mounted on the passenger side. We are looking fabricatiing serpentine set up. Power steering is being handled by electric under dash set up so not necessary for mounting a pump of the motor. If pictures available will post.

4
Member Projects / Re: SOHC mustang convertible longest project ever
« on: October 19, 2018, 01:33:47 PM »
The shop got the motor back in the car. Not a lot of room. Exhaust fabrication to start along with inner fenders. Also bracket fabrication for the air conditioning. Unfortunately going to have to modify the hood for the stacks. Real bummer.
Cannot wait to hear the motor run again.





5
Member Projects / Re: SOHC mustang convertible longest project ever
« on: September 24, 2018, 06:41:03 AM »
Thought there would be more room with front clip. Still restricted because we want to run a 325 tire up front. Unfortunately project has been ongoing for almost 30 years. Have had the car since I was 16 and always seemed something came up. I really like the motor mount design the shop came up with. Way better than what roadster shop sent.



6
Member Projects / Re: SOHC mustang convertible longest project ever
« on: September 20, 2018, 05:54:43 AM »
Thanks Jay
If you did not help me out with that Munro rocker it would of been another delay.
Any updates on your rockers?

7
Member Projects / SOHC mustang convertible longest project ever
« on: September 19, 2018, 02:05:11 AM »
Long story tried notching the towers. Did not give me the warm fuzzy. Went with the roadster shop front clip. Set the motor back extra 3” and modified the firewall, but really worth it I think and it gives it more room for the radiator install. Finally got the motor assembled and ran on the test stand 5.5 hrs and sounded amazing with no issues. Now getting the motor back in the car for exhaust final install and the borla injection install. Some really big challenges to overcome for sure and more to come I have no doubts.
[omg]https://i.postimg.cc/ZvhR33fd/96_F2_B22_B-_C633-4_BB8-8_B70-9_E44165_DD281.jpg[/img]













8
Private Classifieds / Re: 2 canton ford fe oil pans
« on: February 06, 2017, 05:47:58 PM »
Correct email address is sleepyj5@live.com
Appoligise in advance for the confusion.
Regards
Shane

9
Private Classifieds / Re: 2 canton ford fe oil pans
« on: February 06, 2017, 04:18:46 PM »
Have not got your email. Will pm you.
Regards shane

10
Private Classifieds / 2 canton ford fe oil pans
« on: January 29, 2017, 04:41:45 PM »
Have 2 canton fe oil pans for sale. Went with a roadster shop suspension set up so these surplus my needs.

1.0 canton aluminum road race oil pan that I purchased off a member on this site. Used for dyno runs I believe. 425 shipped lower 48. SOLD

2.0 NIB canton 15-850 oil pan / 15-851 pick up / 20-938P windage tray. 325 shipped to the Lowe 48.
SPF....
Email sleepyj5@live.com is the best way to communicate. Travel a lot so it may take a little time to respond.

11
Member Projects / Re: 1968 mustang convertible SOHC project
« on: June 13, 2014, 11:13:08 PM »
Driver side header tacked up. A real challenge for sure. 80 hours so far with the mock up of PVC pipe and tacking and fitting.

12
Member Projects / Re: My 427 SOHC Build..... Finally the time has come!
« on: May 12, 2014, 11:27:32 AM »
Sounds like a really cool build. Especially the EFI set up has my interest. Doing a similar build, just trying to get my headers finished before I send out to the builder. Look forward to reading the updates.

13
Member Projects / 1968 mustang convertible SOHC project
« on: February 23, 2014, 10:51:44 AM »
Long time lurker. My first car. 25 years later. The SOHC was a after thought now that parts are readily available. After meeting financial commitments and family commitments finally got the green light to finish the car. Got the motor mocked up and looking at starting the header fabrication this week. Have the TCP set up so it allows a little more notching of the towers.
Regards

14
FE Technical Forum / Sohc header primary tube sizing
« on: July 06, 2013, 11:04:47 AM »
Just getting ready to fabricate a set of headers for my pond heads. Just curious what size of primaries people are running? Motor is for the street.

15
FE Technical Forum / Re: Pond SOHC Heads......
« on: April 18, 2013, 08:34:33 AM »
Just sent payment to pond. Should have the set of heads and manifold in a couple of weeks. I am anticipating that they will be as high quality as the other components that I purchased from him. Sure has been a long wait. Was going to purchase coon heads now that they are readily available but decided to wait out for the pond heads ,because he actually returned my emails and phone calls.

Pages: [1] 2