Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - rowdy58ford

Pages: [1] 2
1
Vendor Classifieds / Re: NEW ALUMINUM HIGH RISER HEADS AND INTAKE!!!!
« on: December 20, 2019, 12:58:11 PM »
Are these legal for stock eliminator Thunder bolt? AA/S

3
Private Classifieds / Re: BT HR heads, Hogan manifold, valvetrain package
« on: November 11, 2019, 02:35:05 PM »
 What did the heads flow? Had to ask as I run a AA/S thunder bolt blair P motor and run a 519ci cammer in a 63 notch back drag car hasn't made it to the strip

4
Vendor Classifieds / Re: Wanted: Bare 427 M/R heads.....
« on: May 08, 2018, 11:58:18 AM »
I have new and used MR heads newer dates than 1966 graus19260@aol,com

5
Member Projects / Re: New Cammer owner
« on: September 16, 2017, 06:42:41 AM »
What is your SOHC valve spring pressure at the seat?

6
FE Technical Forum / Re: Thinking about casting some valve covers...
« on: March 17, 2017, 11:12:19 AM »
Jay I seen a cool ideal on FE form on the autolight inline carbs there air cleaner has a clear view tops with the groves machined in them,  2x4 w-bird clear top would be cool maybe the bottom clear to see the carbs? Greg

7
Member Projects / Re: New Cammer owner
« on: February 02, 2017, 09:07:58 AM »
Do you know what the spring pressure is valve seat?

8
Private Classifieds / Re: Boninfante billet clutch
« on: January 08, 2017, 09:28:39 AM »
How deep of bell do you need for the clutch?

9
Member Projects / Re: My 427 SOHC Build..... Finally the time has come!
« on: November 21, 2016, 10:24:15 AM »
Put a vacuum pump on the motor!

10
Jay why don't we get together with ARP and get some studs made the 9/16 with a allen in the end to take them out I had called to see if they had any thing close had nothing but could be made I'm sure they will sell. Also kurt was saying that munro was making some rockers are you in contact with him? I need to have a better rocker than stock I like the bushing idea no bearings !

11
Member Projects / Re: My 427 SOHC Build..... Finally the time has come!
« on: September 05, 2016, 08:44:28 AM »
Just a heads up on Keith C C&C machining on coon heads he did my heads and built the motor put on dyno and water blew out of spark plug holes he cut the intake short side and they leaked said send back and  did nothing so my advice is to be sure you get the heads pressure checked and save some time and money!

12
Private Classifieds / M-W 9" 35 spline spool
« on: June 23, 2016, 08:09:48 AM »
9 inch ford mark Williams spool 35 spline only fits M/W axle spline 150.00 plus shipping  SALE PENDING ON SPOOL

13
Private Classifieds / Re: HOLLEY STUFF
« on: April 24, 2016, 07:36:42 AM »
Any of the side hung bowls have the rectangular brass floats?

14
Private Classifieds / Re: WTB USED 427 ALUMINUM 4V INTAKE
« on: April 15, 2016, 10:40:13 AM »
I have a side winder let me know   graus19260@aol.com

15
I see you responded on the intake gaskets HR are they gone?  763 444 0141

Pages: [1] 2