Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ntheogen

Pages: 1 ... 11 12 [13] 14 15 ... 17
181
Private Classifieds / Looking for billet crank and rods...
« on: July 23, 2018, 02:38:48 AM »
I'm looking for a billet crank and rods for my hi riser engine. Bigger the better, let me know what you have that you might part with. Have cash or parts to trade.

Jack 540-664-for four one ate

182
FE Technical Forum / Re: Jarvie Performance castings
« on: July 22, 2018, 12:33:16 AM »
Yes it's Ponds stuff.

183
Private Classifieds / Re: Any 66-67 427 Fairlane Ex Manifolds around?
« on: July 21, 2018, 06:25:50 PM »
You do know they are reproduced

I didn't know that, thanks for the heads up Carl. The deal is done now though, with some unknown tariffs from Canada to the US involved too.

Jack

184
Non-FE Discussion Forum / Cheap shipping from LA to NorCal
« on: July 20, 2018, 01:11:46 PM »
Headed to LA right now to pick up a '27 shortblock. I'll be headed back to the bay area Sat or Sunday. I could transport something smallish if needed, just toss me a few pennies for gas.

Jack 540-664-for four one ate

185
Non-FE Discussion Forum / Re: Just store it or......?
« on: July 17, 2018, 11:56:50 PM »
Hitting very close to home for me as well. I have 4 cars that sit idle in the shop, the 5th car [66 Fairlane GTA] is sort of a daily[?] driver, IF I go anywhere. But since I retired almost 3 years ago and the car club I used to belonged to there is no good reason to drive any of my cars, no place to go, no car club activities to use as an excuse to drive any one of them. No weekend 'road trips' with the wife anymore as traffic around here [S.F Bay Area] really sucks. It's not so bad leaving on a road trip, its the trip home that I hate. [Traffic backed up for miles on a Sunday afternoon/evening] I'm now dealing with stale gas, questionable brakes, flatspotting the tires and leaky seals from sitting. I also hate to sell anything having to deal with tire kickers, wheeler-dealers, wanna-be car flippers and the usual assortment of clowns looking to buy for .05 cents on the dollar as my cars are not show quality perfect but are decent driver quality. Some would say "A 20 footer" I never fill the tank on any of my cars anymore as the gas will just go stale long before it gets used up. If I use a car to go to a local car show I put only 3-5 gallons of gas in the tank or just enough to make the round trip. I keep a 5 gal fuel jug full, with "Stabil" and a shot of Marvel Mystery oil added for such events.   

I'm just outside of SF, I'll come maintain and drive your fleet for you anytime. Lol

Jack

186
Private Classifieds / Any 66-67 427 Fairlane Ex Manifolds around?
« on: July 16, 2018, 12:47:35 AM »
I know it's somewhat laughable but ya don't know until you ask. Let me know if you have any you would part with.

Thanks
Jack
540-664-for four one ate

187
Private Classifieds / Re: Cobra Jet C6 cast iron tail shaft for sale
« on: July 14, 2018, 01:06:47 AM »
My experience has been they sell for around $250, that's what I got for the last one I had. I've personally never seen one sell for anything near that price. Hope this helps.

Jack

188
Private Classifieds / Re: hays mark 12 pressure plates
« on: June 17, 2018, 10:57:36 AM »
Keith I think I've got some hays clutches, I'll look in the next day or two.

Jack

189
I'm in the middle of Kansas on my way back to Northern California and have some parts with me if anyone is interested in any of it. Free delivery along my route.

427/472 Hi Riser stroker engine
I'd sell the shortblock $5500 or
4v top end $4000

Brand new Man O'War Block p/n87182
Je pistons 4.125 NIB
JESEL belt drive setup
Two different cranks - rpm dg3-351cc & eagle 4.00 crank.
Set of NIB probe pistons as well

5k takes all the small block stuff.

540-664-for four one ate

Jack

190
FE Technical Forum / Re: Jay's Clear Vaccum Formed Valve Covers
« on: June 02, 2018, 04:23:04 PM »
Just received mine in the mail and opened them up, they look great Jay thanks so much.

191
FE Technical Forum / Re: C3AE-E crank question
« on: June 01, 2018, 11:01:06 PM »
Just like the c4ae-b cast crank, they were used in both the 390 and 427s.

192
427/472 Hi Riser Engine Package

Freshly machined  030 over 3F3 center oiler block
New RaceTec 4.263 pistons - 11.1
Eagle 4.125 crank
New Eagle 6.700 rods
Fresh Hi Riser heads - very nice
New deep rear sump Mildon pan
C4AE-F 4v intake
Ford adjustable Hi Riser rocker assembly
Crane cam
New professional products balancer
Push rods and odds & ends

$9,500

Pics available upon request
540-664-for four one ate
Jacksfordparts geemail

Jack

193
Private Classifieds / Re: 428 CJ Engine - Really Nice Mill
« on: May 29, 2018, 09:59:06 AM »
Forgot price - edited ad

194
Private Classifieds / 428 CJ Engine - Really Nice Mill
« on: May 28, 2018, 08:27:47 PM »
428 CJ for sale. 72 dated 040 over service block. CJ heads. Dove roller rockers. Ferrea valves 10 to 1. Speed pro pistons. Scat cast 3.98 crank. Eagle rods. Crower 650 solid roller. MSD dist. Edelbrock alum water pump. 2x4v Ford 427 Low Riser Intake with C80F 9510 AC and AD carbs. Carbs have tags. Arp bolts. All pulleys fan, alternator and brackets. ATI balancer, Canton Pan. Coated headers. Nice engine. Lots of machine shop paperwork. Engine is together and turn key, has less than 250 miles on it.

Located in VA

8k

Can text or email pictures or they're loaded up at the other fe forum site.

Jack 540-664-for four one ate
Jacksfordparts geemail

195
Private Classifieds / Re: WTB Aftermarket 27 Block
« on: May 24, 2018, 08:03:23 PM »
Meant Dennis and he doesn't not have any.

Pages: 1 ... 11 12 [13] 14 15 ... 17