Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - preaction

Pages: 1 ... 10 11 [12] 13 14 ... 18
166
FE Technical Forum / Re: Clutch Issues
« on: September 15, 2017, 04:23:49 PM »
I have a T56 with a Ram hydraulic bearing and twin disk RXT in my 68, it was very hard to get bled but once I got there it has been working great. I do remember having to have to change the trans snout to get it right.

167
Private Classifieds / Re: Complete S Code 390, GT ex mainfolds
« on: September 12, 2017, 04:11:09 PM »
Scott anyone buying these will use them in a  restoration so the dates on them might help someone.

168
FE Technical Forum / Re: Good Buy or Not ? "Tunnel Port Top End $5,500"
« on: September 01, 2017, 05:02:04 PM »
Brent do you have an idea where the TP heads wind up flow wise ?

169
Member Projects / Re: Billet Intake Manifold for the Tunnel Port Intake Adapter
« on: August 27, 2017, 08:16:35 PM »
From your posts of the issues you were having with the ABS then the PLA plastics warping and questions of heat survivability, did I miss your getting a better plastic ?

170
Member Projects / Re: Paul Munro gear drive
« on: August 27, 2017, 07:36:46 PM »
Jay what are the configuration of the 2 Monroe SOHC intakes ?

171
FE Technical Forum / Re: FE engine build books ?
« on: August 27, 2017, 07:29:36 PM »
That's great Barry I would say that adds up to very successful for anything FE. 8)

172
Member Projects / Re: Billet Intake Manifold for the Tunnel Port Intake Adapter
« on: August 27, 2017, 07:23:35 PM »
Quote from: jayb on August 27, 2017, 09:08:25 AM
Nope.  ???
its PVC with a very high heat resistance.

173
Member Projects / Re: Billet Intake Manifold for the Tunnel Port Intake Adapter
« on: August 26, 2017, 10:36:52 PM »
Jay are you familiar with CPVC plastic ?

174
FE Technical Forum / Re: BBM block dimensions
« on: August 26, 2017, 07:07:59 PM »
Does anyone know of a reason for the clearance on these caps (1&5) and not a tight fit for the front and back  ?

175
FE Technical Forum / Re: BBM block dimensions
« on: August 26, 2017, 12:27:16 PM »
Good as that's what I have too, I thought all were close fit.

176
FE Technical Forum / Re: BBM block dimensions
« on: August 26, 2017, 12:25:57 PM »
The first two are the front cap last two are the back cap. What are my options?

177
FE Technical Forum / Re: BBM block dimensions
« on: August 26, 2017, 12:15:00 PM »
Thanks Brent my first and last main caps can fit a .020 feeler on both sides. I will post  some pics.

178
FE Technical Forum / Re: FE head dowels
« on: August 25, 2017, 09:46:41 PM »
My napa said no even in a much later 460 application.

179
FE Technical Forum / BBM block dimensions
« on: August 25, 2017, 08:25:28 PM »
Should there be any clearance between the first main cap  and the sides of the register in which its installed and tightened down not torqued down and without a crank or bearings ?

180
FE Technical Forum / Re: FE head dowels
« on: August 25, 2017, 06:13:49 PM »
Barry shows a pic of a black one in his book Im guessing its aluminum.

Pages: 1 ... 10 11 [12] 13 14 ... 18