FE Power Forums
FE Power Forums => Private Classifieds => Topic started by: Nightmist66 on April 09, 2017, 10:04:18 PM
-
Up for sale is a set of used Edelbrock 6005s. These have a few hundred street miles on them. I have not run them, but purchased them from a friend who took them off a running motor. When I got the heads, they had a decent set of springs/retainers/keepers that matched my cam better that was in my car at the time, so I swapped out my old ones for the ones on these heads. The current springs on these heads I would NOT run. I put them on to make them complete. They checked at around 80-90 on the seat and about 215-225 open at .560" lift. The drainbacks I enlarged to 1/2" and radiused, but did not touch the intake side yet. The oil feed slot has been radiused at the edge leading into the head bolt hole on each. No porting on intake or exhaust. Minor pitting at a couple coolant ports on intake side. Should seal fine w/small dab of rtv.
Price is $975 free shipping within US
(http://i12.photobucket.com/albums/a232/jaredaebly/20170408_122044_zpswpnow25s.jpg) (http://s12.photobucket.com/user/jaredaebly/media/20170408_122044_zpswpnow25s.jpg.html)
(http://i12.photobucket.com/albums/a232/jaredaebly/20170408_122111_zpshntwaju6.jpg) (http://s12.photobucket.com/user/jaredaebly/media/20170408_122111_zpshntwaju6.jpg.html)
(http://i12.photobucket.com/albums/a232/jaredaebly/20170408_122321_zpstaoxjsob.jpg) (http://s12.photobucket.com/user/jaredaebly/media/20170408_122321_zpstaoxjsob.jpg.html)
(http://i12.photobucket.com/albums/a232/jaredaebly/20170408_123042_zpsclavv8h0.jpg) (http://s12.photobucket.com/user/jaredaebly/media/20170408_123042_zpsclavv8h0.jpg.html)
(http://i12.photobucket.com/albums/a232/jaredaebly/20170408_123805_zpsxyw0qxfj.jpg) (http://s12.photobucket.com/user/jaredaebly/media/20170408_123805_zpsxyw0qxfj.jpg.html)
-
I sent you an e-mail on these by clicking on your profile.
-
I'm sorry, but I haven't seen an email yet. I will send you a PM.
Thanks, Jared
-
Still for sale.
-
$975 and free shipping within US
-
What are the valve sizes?
-
Are they the original 2.09/1.65 valves? Do you know the actual chamber size? Thanks
-
What are the valve sizes?
Factory installed CJ size.
-
Do you know the actual chamber size?
Supposed to be 72cc. I have not actually cc'd any chambers yet. Can if you would like. As far as I can tell, heads were never milled.
-
Jared,
If you could pour one chamber that would be great, last set of 6005 edel's I had my hands one were closer to 80 cc's before I milled them a bunch. Also where are you located in IL ? I'm going to be down there working next weekend, possibly save time/money on shipping if we can meet up? Also I can't use the used springs or retainers, waaay to light on psi for my junk, and I'd prefer to buy just the valves and heads if possible? That way I could also verify the valve guide and seat condition... let me know, thanks
-
Cody, I will try to get a chamber measured for you. I am located in northern IL, about 2 1/2hrs west of Chicago. I can take the springs/retainers off if need be. I will PM you some more contact info. Thank you.
-
I CC'd the end chambers on both heads. One head was 73.5cc's on both ends. The other came out 73.5cc and 74cc. I used an NGK BKR5E plug for checking.
-
Sale pending...
-
If cody changes his mind , i would like to be next in line.
-
Hi Jaime. Someone PM'd me after Cody inquired. You are third in line.
Thank you, Jared
-
What material are the retainers made from please
Also, if you sell heads without springs/retainers/keepers are you keeping them ??
Ricky.
-
Ricky,
the retainers are just plain old steel. I think I may just keep them if I don't sell them. I will let you know if/when something happens.
Thanks, Jared
-
Thanks Jared
Ricky.
-
Sold, pending payment.
-
Heads are sold. Thanks for the space here Jay!
-
winr1/Ricky-
Thank you for inquiring. I have decided to keep the leftover springs, retainers, keepers.
Thanks again, Jared