Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - hbstang

Pages: 1 [2] 3 4
16
Private Classifieds / 1968 mustang cobra jet exhaust manifolds
« on: April 18, 2021, 09:12:30 PM »
passenger long manifold has a crack that was welded?it was not crack all around.see pics.asking $1800 plus shipping.i have never used these and dont know who did the work.i dont see any other breaks or damage.

17
Non-FE Discussion Forum / coupe to fastback mustang conversion?
« on: October 17, 2020, 01:39:06 PM »
has anyone here done this?have a 68 coupe with a lot of mods,and would make a nice fastback as a hot rod.not a restored car,but more of a street/strip car.i have seen videos on them,but they offer little real details or info.

18
Non-FE Discussion Forum / anyone done this setting pinion angle on caltracs
« on: October 15, 2020, 04:53:06 PM »
64 fairlane with caltracs,and their split mono leafs,i was told to set between 2-4 degrees pinion angle to crank centerline.9 inch is not welded to perches yet,thats where i am at right now.any one done this?
anyone have any real world results?i have it set at 4.2 right now,and was told rear will want to change that on launch.

19
Private Classifieds / block
« on: August 14, 2020, 02:09:04 PM »
gone







20
Non-FE Discussion Forum / another 64 fairlane question!
« on: August 04, 2020, 06:28:53 PM »
on the rear window of a 2 door sedan,how does the window trim fit in?is there a clip that goes in the rubber seal?any pictures of that?can you install the window with out the clips?i cant find any info on them on the web.lol.

21
Private Classifieds / headers and exh system for galaxie not mine seems cheap
« on: July 08, 2020, 01:39:05 PM »
on ebay.
https://www.ebay.com/itm/Complete-3-inch-Exhaust-System-for-63-Galaxie-427-with-Ceramic-Coated-Headers/114289682321?_trkparms=aid%3D111001%26algo%3DREC.SEED%26ao%3D1%26asc%3D20160811114145%26meid%3D7cc43d2ae4c248d9b689d1fa4d3a1799%26pid%3D100667%26rk%3D5%26rkt%3D8%26mehot%3Dnone%26sd%3D303616860958%26itm%3D114289682321%26pmt%3D0%26noa%3D1%26pg%3D2334524&_trksid=p2334524.c100667.m2042

22
Non-FE Discussion Forum / any one in canada ab have an empty trailer going to us?
« on: June 26, 2020, 04:30:45 PM »
trying to buy a race car close to calgary canada and was looking for advice on shipping or moving the car to the states?anyone here do that?

23
Non-FE Discussion Forum / headliners!
« on: June 12, 2020, 10:37:41 PM »
what does everyone do if they have a full roll cage in there 64 fairlane for a headliner?i think i can get a stock one in with the bows but it will be tight.i like the stock looks,but i wanted to see if anyone has ideas,such as a glue in cloth?

24
Private Classifieds / wtb 66-67 fairlane fe motor mounts and brake/clutch pedal-found
« on: June 08, 2020, 10:59:18 PM »
looking for the 6 pieces for factory fairlane fe motor mounts,and clutch and brake pedal assembly.what do you have and how much?pm for contact info.dont need them now  !

25
Private Classifieds / mustang 68 69 brackets and pulleys ps pump 428 engine
« on: May 30, 2020, 03:41:51 PM »
all parts in southern cal.all parts plus shipping.pm for more pictures
428 engine with pi block,lemans rods,forged pistons,mild port C80E-N heads,hyd roller cam.performer rpm,comp roller rockers,msd dist,custom 750 holley,deep pan,maziere pump,chrome alternator,auto flexplate,ready to drop in and run.engine has low miles,and runs great.makes good power!will include coated hooker headers for a 67-70 mustang.asking $6500.if you want it shipped,it would run about 500-800 dollars plus custom crate.


1) heater motor bracket  used on 390 428 engine cars----------$60
2)power steering bracket  only    ---------------------------------$75
3) C8AE A & B alternator brackets --------------------------------$150
4)C8AE smog bracket,nice chrome on it --------------------------$125
5)power steering pump,braket,AFpulley,not stuck,dirty ----------$125
6)c8ae -b crank pulley 3 sheeve------------------------------------$60
7) C8AE-e crank pulley 2 sheeve --------each----------------------$75

26
Private Classifieds / wtb 64 fairlane FOUND
« on: May 06, 2020, 03:40:14 PM »
looking for the small rods that link to the door handle/lock and door latch.there is 4 per side i only need the 3 short ones on the drivers door.any help?this is for a 64 fairlane 2dr sedan,so i dont know if other cars  wil fit.

27
Private Classifieds / 1964 fairlane 2 dr sedan parts,new glass
« on: April 23, 2020, 04:33:07 PM »
sorry,not fe, parts are for 2 dr sedan..have a drivers door with dent from failed hinge stop!surface rust and no other parts.$150 and no shipping!

rear seat bottom only.this is from a 2 door sedan,surface rust and no rust holes.seat covers are bad of course.asking $150.will  ship the seat bottom.buyer pays actual.

also,have front suspension parts,upper and lower control arms etc,pm for what you may want.these are all stock used parts.strut rods,etc.

also have new glass for 2 door sedan.its for door windows,1/4 windows and vent windows,all grey tint.$225 for all plus high risk shipping.

28
Private Classifieds / parts sold
« on: March 04, 2020, 06:50:54 PM »
parts in southern cal.pm for contact.

parts sold.

29
Member Projects / 1964 fairlane interior paint
« on: March 01, 2020, 07:49:06 PM »
for those that have done or are working on a 64 fairlane with the beige/tan interior color,what did you use for paint color or codes?this is for the trim,dash,and top and bottom of the doors.one paint code i found online was a medium beige poly ditzler 22396.is that close enough?and where to buy it?

30
Private Classifieds / 1969 mustang fastback pro street gone
« on: February 15, 2020, 06:28:29 PM »
car is in southern cal. SOLD GONE!
this car has been a race car for 40 years.no title,but does have the vin tag on the dash,and front inner fender apron is stamped.has the old school supertricks on it,tires are dead.has nodular ford 9 inch with spool 4.86 pro gears and 45 spline axles!all windows are foggy lexan..only rust is front floor pans.rear is full tub and can take a larger tire.engine compartment is in decent shape,no rust on front frames or torque boxes.all frames are nice and solid.pm with contact info.car is in southern cal,and if you can find someone to ship it,the car rolls and steers fine.

Pages: 1 [2] 3 4