1
FE Technical Forum / Re: oil gallery
« on: March 14, 2024, 10:36:34 PM »
RE tap too big for 3/8 drive:
Can you use use a 1/4 drive socket?
Can you use use a 1/4 drive socket?
Dedicated to Building and Racing the Ford FE Engine
News:
SMF - Just Installed!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
FE Technical Forum / Re: Spark plugs for BBM heads
« on: March 14, 2024, 10:29:35 PM »
Compression ratio is unknown, that's why I'm ccing the heads. I'm guessing 10.5, hoping for 11.5, would be delighted with 12.5.
3
FE Technical Forum / Spark plugs for BBM heads
« on: March 13, 2024, 09:28:36 PM »
I paln to CC my BBM heads but then realized they use a smaller spark plug than the one in the stock heads.
So what plugs shold i be getting for track use.
And I just realized the plugs I've been saving (including a a set or two of Holley spark plugs) will be of no use to me - lol.
So what plugs shold i be getting for track use.
And I just realized the plugs I've been saving (including a a set or two of Holley spark plugs) will be of no use to me - lol.
4
FE Technical Forum / Re: Bear Block Motors FE heads in stock, if I am reading the web page correctly
« on: March 03, 2024, 11:55:17 PM »
message sent
5
Vendor Classifieds / Re: FS: New in box LSM-600 Bench Top Valve Sping tester
« on: February 12, 2024, 11:02:23 PM »
Private message sent
6
Private Classifieds / Re: Wanted ford fe oil slinger nos #B8A-6310-A
« on: December 29, 2023, 10:49:11 PM »
I probably have one as I stripped several Edsel engines and kept all of the small parts. Do you have a picture or tell me what is different from the standard oil slinger so I can be sure?
7
Non-FE Discussion Forum / Re: Pomoma # 1 Qualifier Stock Elimanator
« on: December 21, 2023, 10:14:30 PM »
Unbelievable, 77 years old and his reflexes still let him be the number one qualifier.
8
Non-FE Discussion Forum / Re: Calliope Engine Project
« on: December 21, 2023, 10:07:44 PM »
Wow, a very neat project. Lots of little parts will have to be made to complete it.
We should start a betting pool for the date the engine makes its first complete dyno pull.
This engine also gives a very different meaning to twin cams.
We should start a betting pool for the date the engine makes its first complete dyno pull.
This engine also gives a very different meaning to twin cams.
9
FE Technical Forum / Re: CVR Water pump inlet tubes
« on: December 18, 2023, 01:06:53 PM »
They apparently don't sell direct. I emailed them; they told me their re-seller was Summit. I ordered from Summit, shipping is estimated for Feburary 29th.
CVR suggested I have it dropped shipped and I'm trying to get that to happen.
CVR suggested I have it dropped shipped and I'm trying to get that to happen.
10
FE Technical Forum / CVR Water pump inlet tubes
« on: December 15, 2023, 01:31:42 PM »
No one has these inlet tubes.
Would a Morso inlet 62522 fit?
Would a Morso inlet 62522 fit?
11
Private Classifieds / Re: WTB FE Power valve covers.
« on: December 12, 2023, 09:45:39 PM »
Msg sent.
12
FE Technical Forum / Re: Header flanges for BBM heads
« on: December 07, 2023, 06:58:14 PM »
Thanks I will give him a call.
13
FE Technical Forum / Older Napa Ignition module
« on: December 07, 2023, 06:09:26 PM »
I have two FE distributors with NAPA pointless conversion setups installed. It has been so long since in used them I do not recall what electronic modules work with them. I used them with MSD boxes back in the day but I also used them with the NAPA module and some Ford modules.
Does anyone recall using these?
Does anyone recall using these?
14
FE Technical Forum / Header flanges for BBM heads
« on: December 06, 2023, 11:07:24 PM »
Does anyone have a recommendation for header flanges for the BBM head?
Thanks
Thanks
15
Private Classifieds / Re: 427 side oiler block for sale
« on: November 08, 2023, 10:53:21 AM »
Block is no longer available.