A flow bench does all of it's work on the chamber side.  When flowing exhaust you reverse the flow and open the exhaust valve, so there would be no way to have it push on the exhaust and suck on the intake at the same time

However, if you did want to optimize, you could chase low lift flow on the intake side, I am no porter, but that doesn't always help higher lift.  Best is to have a port that is clean and not too much volume

On edit - here is a cleaned up video from the owner

Glad he could, it is a pretty engine

https://www.youtube.com/watch?v=mtgO0UFeXIA

Too funny! Special cam stays open 10 times as long, more power!

Performance Summary:
      Cubic Inches:  457             Dyno brand: Stuska
      Power Adder:  N/A             Where dynoed:  Dale Meers Racing, Buffalo, KY
      Peak Horsepower:  528@5900
      Peak Torque:  555 @ 4000


Engine Specifications:
   Block brand, material, finished bore size, other notes:  1969 C scratch 428, 4.150 bore, CnC squared, aligned, torque plate honed
     
   Crankshaft brand, cast or forged, stroke, journal size: SCAT cast 4.25
     
   Connecting Rods brand, material, center to center distance, end sizes, bolts:  SCAT I-beam 6.700

   Piston brand, material (caster, hypereutectic or forged), dish/dome volume, static CR: Racetec, 14 cc dish, 10.03:1

   Main Bearings, Rod Bearings, Cam Bearings brand and size:  Clevite rod and main bearings, Durabond cam bearings

   Piston rings brand, size, other notes: Mahle 1mm/1mm/2mm standard tension

   Oil Pump, pickup, and drive:  Melling M57HV, Canton pickup, ARP drive

   Oil pan, windage tray, oil filter adapter:  Cobra aluminum repop, no tray, factory oil filter adapter

   Camshaft brand, type (hyd/solid, flat tappet or roller), lift and duration (adv and @.050"):  Custom Bullock's Power hydraulic roller, 237@.050 intake

   Lifters brand, type:  Morel standard travel

   Timing chain and timing cover: Cloyes 9-position roller, Roush alum timing cover

   Cylinder heads brand, material, port and chamber information:  C8OE-N CJ, Les Schmader ported, 3/8 unknown aftermarket undercut stem valve, 2.09 intake, 1.67exhaust, Viton seals, ID spring locators

   Valve springs: Crower 160/420
 
   Rocker arm brand, type (adjustable or non-adj), material, ratio:  Factory nonadjustable, 1.73

   Rocker shafts and stands, brand, material:  Harland Sharp shafts, Trick Flow studs, Precision Oil pump end stands

   Pushrods brand, type, length:  Custome Smith Brothers 5/16, 3/8 ball/ball non-oiling

   Valve covers, brand, type:   69 CJ aluminum

   Distributor brand, advance curve information:  Pertronix billet, 38 total

   Harmonic balancer brand:  Stock, restored

   Water pump brand, type (mechanical or electric):   Tuff Stuff aluminum- electric powered on dyno

   Intake manifold brand, material, porting information:  Blue Thunder CJ, with divider notch cut

   Carburetor(s) brand, type:  750 dyno carb, but engine will run a Terminator Stealth

   Exhaust manifolds or headers brand, type:  Dyno headers

Quote from: My427stang on May 01, 2024, 04:51:29 PM

I didn't even think of that when I asked Jay if I could hang my Cleveland results, sort of an obvious and fair option.  My email to him was actually, "where did the non-FE dyno page go? " But it never existed.  Not sure why I thought it did

It does exist:
FE Power Forums »FE Power Forums »Non-FE Discussion Forum
https://fepower.net/simplemachinesforum/index.php?board=3.0

There is no dyno section there, period, and I contacted the forum owner directly before I posted.  If he would have said put it there, I would have put it there.  As much as I would like to push back, you get a little credit, that is a good idea.

Nobody is fighting you here, you seem to think that Jay saying it's OK beforehand wasn't enough, and you keep changing what you are upset about... I have no beef with any of this, but you can't argue what the forum owner says, it isn't my forum and it isn't yours....just let it go.

BTW - On edit - Go look at the forum you are trying to keep pure...3 Y-blocks, 1 Boss, and 3 MELs before our Clevelands showed up.  This isn't new

I thought you all may find this interesting

459 inch 428, BT intake, iron heads, SCAT crank and I-beams, Racetecs, hyd roller, Morels, alum water pump, no flywheel, no carb, engine stands bolted on, with 7.5 qts oil - 529 lbs
433 inch 428, CJ iron intake, iron heads, Ford Crank, Molnar rods, Racetecs, hyd roller, Morels, iron water pump, no flywheel, no carb, engine stands bolted on, 6 qts oil -582 lbs

Figured I'd weigh them for laughs..off to the pump!  Even a Ram 2500 HD has a little squat with these two big girls in the back!

Great build Brent.