Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Saltshaker

Pages: 1 [2] 3 4 ... 9
16
Private Classifieds / Re: 3/8 steel header flanges
« on: November 09, 2021, 02:31:08 PM »
$29.00 from the post office. fyi, I’m leaving on friday on vacation for a wk… I can ship them tomorrow or Thur
Jon

17
Private Classifieds / Re: 3/8 steel header flanges
« on: October 24, 2021, 04:57:27 PM »
I’ll check with the post office tomorrow and let you know
Jon

18
Private Classifieds / 3/8 steel header flanges
« on: October 24, 2021, 09:13:11 AM »
Free! Cleaning out the garage.., just pay shipping from 07746 Nj
Jon

19
FE Technical Forum / Re: Carb Hesitation
« on: July 22, 2021, 11:49:43 AM »
same wt, but this car has a automatic with a 1800-2200 converter
Jon

20
FE Technical Forum / Carb Hesitation
« on: July 21, 2021, 06:39:37 PM »
Engine ran flawlessly in my old car but I needed to remove the 1” open spacer from the rpm intake and it now hesitates off the line. Would removing the spacer cause this and any suggestions for a cure?
Jon

21
Private Classifieds / Petronix Digital Hp box (New)
« on: May 30, 2021, 01:19:17 PM »
Petronix HP digital box $232@ Summit $175 plus shipping from Nj
3 step digital rev limiter
adjustable start restart
rpm trigger output
Jon

22
FE Technical Forum / 3G top mounted Alt
« on: November 26, 2020, 07:40:35 AM »
I want to swap alt and use a 3g single pulley alt with factory brackets...is it the sm or lg case unit that will work?
Jon

23
FE Technical Forum / Re: 6an ptfe fuel line big enough?
« on: October 08, 2020, 04:53:52 PM »
thnx every one...will try 6an and see how it works
jon

24
FE Technical Forum / 6an ptfe fuel line big enough?
« on: October 07, 2020, 11:51:30 AM »
my tank has a 3/8 pick up and the motor is around 500 hp ... is 6an ptfe big enough? it measures .32
which isn’t 3/8...
Jon

25
Private Classifieds / Re: Free Johns 9” Rear
« on: August 11, 2020, 07:46:36 PM »
Send me your email address
Jon

26
Private Classifieds / Free Johns 9” Rear
« on: August 10, 2020, 04:23:11 PM »
Came out of a Cobra, 49” wide  Large bearing ....1 tube rewelded with a bar....set up for triangulated 4 link.
MUST pick up in Englishtown, NJ
Jon

27
FE Technical Forum / Re: 2500 rpm stall
« on: July 26, 2020, 07:41:34 PM »
Thanks for explaining
Jon

28
FE Technical Forum / 2500 rpm stall
« on: July 26, 2020, 06:25:07 AM »
can someone explain what this means? I want to put a C6 or C4 in my car and this converter was recommended. How is it different then the stock converter?
Does TCI make a good transmission?
Jon

29
Private Classifieds / what’s this worth?
« on: July 23, 2020, 08:25:51 PM »

what is a TKO600 road race trans .082 od with a speed shifter, Lakewood Bell housing(bottom cut for a Cobra) hyd clutch slave w/mounting bracket and 7/8 MC, fork plus a fly wheel new clutch disc and 3 finger Ram pressure plate?
Jon

30
FE Technical Forum / fuel line question
« on: July 15, 2020, 06:50:35 PM »
what size fuel line is needed...3/8 or 1/2”? I can get a tank pick up for both. Engine is 411 rwhp with a Carter mech pump. Both outlets are 1/4ntp. Is it worth having a return line to the tank with a Mech pump?
Jon

Pages: 1 [2] 3 4 ... 9