1
Private Classifieds / C5AE-F Medium Riser Head
« on: September 01, 2023, 06:05:56 AM »
In need of one 427 medium riser head or a pair. My NOS head had a crack between 6 and 7 and is unrepairable
Dedicated to Building and Racing the Ford FE Engine
News:
SMF - Just Installed!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
FE Technical Forum / OE 427 Side Oiler Build
« on: May 06, 2023, 05:34:42 AM »
We found two used side oiler blocks that were originally used in a tractor pull setup and damaged. The one needs three sleeves and the other has just been align honed
and in order to straighten it needed the deck cut to 10.133. It looks like it will clean up at 30 over but we'll find out for sure Monday when it goes into the CK-10 boring
machine. My question is will I need to have the pin height shortened when I order pistons? I would like to keep the compression around 10ish. We just finished the NOS
Medium Riser heads with 2.19 and 1.75 SS valves that came from DSC and the cc's came in at 86. Once we get the bore size determined we'll call Diamond for pistons.
Rod length will stay at 6.488 and an original steel crank will be used. I hope my question is clear as I seemed to ramble a bit. Thanks for any info you would like to share.
and in order to straighten it needed the deck cut to 10.133. It looks like it will clean up at 30 over but we'll find out for sure Monday when it goes into the CK-10 boring
machine. My question is will I need to have the pin height shortened when I order pistons? I would like to keep the compression around 10ish. We just finished the NOS
Medium Riser heads with 2.19 and 1.75 SS valves that came from DSC and the cc's came in at 86. Once we get the bore size determined we'll call Diamond for pistons.
Rod length will stay at 6.488 and an original steel crank will be used. I hope my question is clear as I seemed to ramble a bit. Thanks for any info you would like to share.
3
FE Technical Forum / Dick Brannan
« on: October 12, 2022, 06:18:57 PM »
I just received a phone call that said that Dick Brannan had passed away. Does anyone have any info about this?
4
Private Classifieds / CrossBolt spacers and bolts
« on: September 28, 2022, 10:58:02 AM »
Does anyone have or know if the cross bolt spacers and bolts are available? I need two sets.
5
Private Classifieds / '66 Fairlane Door Panels
« on: November 28, 2021, 08:52:54 AM »
I finally received the door panels I ordered in January 2020 but I dyed a set that I found and now I have no use for these. Ivy Gold.They
cost me $300 so I will sell them for that plus shipping from 46371
They are still available 1/29/22
cost me $300 so I will sell them for that plus shipping from 46371
They are still available 1/29/22
6
Non-FE Discussion Forum / Fuel regulator
« on: July 27, 2021, 07:05:31 AM »
Has anyone ran across the same issue as I have with the Holley 803 regulator reading different pressure out of the two Ports?
I am feeding two Holley 450 cfm on a crossram intake and have a gauge on each outlet. When I adjust the pressure to 4.5
the other gauge reads 6 lbs. I have switched the gauges and replaced the regulator but they still read 1.5 lbs different.
I am feeding two Holley 450 cfm on a crossram intake and have a gauge on each outlet. When I adjust the pressure to 4.5
the other gauge reads 6 lbs. I have switched the gauges and replaced the regulator but they still read 1.5 lbs different.
Pages: [1]