Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - machone

Pages: [1] 2
1
FE Technical Forum / Jay's Cleveland intake tests
« on: July 06, 2020, 10:18:30 PM »
Where do I find the dyno results for these? Also what was the best Cleveland intake tested?

2
Vendor Classifieds / Re: D1ZX-9425-FA Dominator intake for sale....
« on: January 04, 2018, 03:36:59 PM »
And any pictures of the intake?
Thanks

3
Vendor Classifieds / Re: D1ZX-9425-FA Dominator intake for sale....
« on: January 04, 2018, 03:35:26 PM »
Hi Brent
Is that the 6464 Dominator?

4
FE Technical Forum / Re: Fuel pump bolts
« on: October 11, 2016, 04:38:38 AM »
Drew,
Took the fuel line off at carb and put line in a bucket, turned her over and plenty of fuel there, so indicates pump is fine.
Suspecting something wrong in the carb?

5
FE Technical Forum / Re: Fuel pump bolts
« on: October 10, 2016, 05:30:00 PM »
Drew, was running fine before hand?

6
FE Technical Forum / Re: Fuel pump bolts
« on: October 10, 2016, 03:27:08 AM »
Ok, fixed the fuel pump mounting issue by inserting a stud in one hole and a longer bolt in the other.
Now , car wont start/run, if it does its very rough, then dies

Thinking it might be a carb issue? Your thought please.

Thanks again
Naz

7
FE Technical Forum / Fuel pump bolts
« on: October 09, 2016, 05:44:47 AM »
Hi,
Just noticed my fuel pump was hanging off the engine, hence why it wouldn't idle and ran so rough.
Stripped threads so, what size tap should be run through the threads and what size are the correct bolts?

Thanks
Naz

8
FE Technical Forum / Re: Accel Distributor ID
« on: September 13, 2016, 07:10:16 PM »
Thanks for the Info guys!

9
FE Technical Forum / Re: Accel Distributor ID
« on: September 10, 2016, 03:43:43 AM »
I have been informed that its for a marine application, thats why the points are hidden under the cover.
Not sure about its performance application though?

10
FE Technical Forum / Re: Accel Distributor ID
« on: September 09, 2016, 09:30:16 PM »
Quote from: Faron on September 08, 2016, 11:05:19 PM
Its a 370000 Series Whats the Question ??
Thanks Faron, I realise its an FE one, but what type, points, electronic?


11
FE Technical Forum / Accel Distributor ID
« on: September 08, 2016, 08:44:22 PM »
Hi
 Can anyone identify this Accel distributor for me?
Part No. 37200, Serial No: F44250

Thanks
Naz

12
FE Technical Forum / Re: Installing a solid cam
« on: May 30, 2016, 12:35:49 AM »
Ok, thanks guys.

13
FE Technical Forum / Re: Installing a solid cam
« on: May 29, 2016, 07:34:13 PM »
Jay
Thats probably what I needed to know.
So as someone suggested do I need to run EDM lifters or regular solids?

Thanks
Naz

14
FE Technical Forum / Re: Installing a solid cam
« on: May 27, 2016, 08:13:47 PM »
So, with my CJ block installing the modified shell lifters (EDM's i take it) is sufficient as a primary step to going to a solid cam?

Modifying the oil passages is also recommended but not necessary?  Motor is in car and running so I might want to avoid drilling and tapping oil passages(unless it can be done in car)?

thanks guys

15
FE Technical Forum / Re: Installing a solid cam
« on: May 27, 2016, 01:36:20 AM »
Ok, I have adjustable rockers and shaft end supports already, just wasnt sure about the oiling restriction side of it, but if I can use EDM lifters then no problems I hope.
Plan on running the Comp cams FB294B-8, with the appropriate springs, retainers, locks.
What type of pushrod should I get?
Naz

Pages: [1] 2