Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - cattleFEeder

Pages: 1 ... 11 12 [13] 14
181
FE Technical Forum / Re: FE Power Stickers
« on: February 07, 2017, 10:06:21 PM »
Fear begins with FE, is a neat one that's been around

182
FE Technical Forum / Re: Any benefit for carb spacers on a 1963 2x4 intake with two 1850's?
« on: January 19, 2017, 10:41:30 PM »
carb spacers canton https://www.summitracing.com/parts/ctr-85-152/overview/
Stay with a four hole on this intake , they get unhappy with an open spacer.
Headers are sanderson shorty
Air filter is blue thunder#ACE-2.25 try Barry at survival motorsports he was back ordered when I ordered mine I ended getting it online from holmanmoody.
www.holmanmoody.com
www.survivalmotorsports.com

183
FE Technical Forum / Re: Any benefit for carb spacers on a 1963 2x4 intake with two 1850's?
« on: January 19, 2017, 01:23:11 PM »
I am running a 1/2" on mine, base plate needs  help to clear dizzy.
I am running a 2.25" air cleaner on mine and its just clears the hood on 63.5 galaxie

184
Non-FE Discussion Forum / Re: Rust removal
« on: December 02, 2016, 07:51:29 AM »
I have seen some pretty amazing projects using this method.
   http://www.7173mustangs.com/thread-molasses-to-remove-rust                               

185
FE Technical Forum / Re: Solid lifters
« on: September 18, 2016, 09:18:43 AM »
Thanks for all the replies,. but we will not be able to use this block, this is the 2nd factory block we have found this way. I am putting money down on a BBM iron block that hopefully we will have in 30 days

186
FE Technical Forum / Re: Solid lifters
« on: September 14, 2016, 12:32:48 PM »
Thanks Brent , that's what I had heard , so I thought ask the experts on here.

187
FE Technical Forum / Solid lifters
« on: September 14, 2016, 08:38:42 AM »
Are there any reasons to run a flat tappet lifter over a solid roller lifter on the street?
The block is not drilled for a hydraulic cam, its a factory block being stroked to 482 cubes.

188
FE Technical Forum / Re: whats alu. cj heads are good and avilable right now
« on: September 11, 2016, 01:15:38 PM »
Felony heads are also very good heads from survival motorsports, and they are all USA made.

189
FE Technical Forum / Re: 427 side oiler date code
« on: August 26, 2016, 10:22:43 PM »
Thanks for all the info guys, but starting Monday this block is coming back to life as a 482. It has sat bare for 30 years.

190
FE Technical Forum / Re: 427 side oiler date code
« on: August 25, 2016, 06:15:02 AM »
Thank you, didn't know they made side oilers that late. When did they stop casting them?

191
FE Technical Forum / 427 side oiler date code
« on: August 24, 2016, 09:24:43 PM »
Does anybody know how to decipfer this block ?

192
FE Technical Forum / PCV for a low riser 2X4
« on: May 03, 2016, 06:28:42 AM »
Should I try getting a pcv valve hooked up to vent tube  on my manifold, I have  pentroof valve covers? Right now it just vents out under the car. I was going to just hook up to the rear carb , will that work?

193
FE Technical Forum / Re: Cam Choices
« on: January 04, 2016, 01:39:22 PM »
On my 63.5 galaxie it has sanderson shorty headers with a toploader behind a 428.

194
FE Technical Forum / Re: Suggestions on a few final parts I need...
« on: December 28, 2015, 07:33:16 AM »
For your water neck canton racing makes a alum billet piece part #CTR 80-058.
I have used this nice part , just smaller hose size than stock, and pricey.

195
FE Technical Forum / Pro Maxx Heads
« on: November 24, 2015, 08:25:45 PM »
http://www.jegs.com/p/ProMaxx-Performance/ProMaxx-MAXX-Series-Ford-FE-Aluminum-Cylinder-Heads/3462220/10002/-1

What am I missing, have these heads been out for a while? I never heard of them.

Pages: 1 ... 11 12 [13] 14