Both in good condition.

The 66 cover is bare, threads are good   $37

The C8AE cover has either a Aug or Sept 69 date code, includes 390 pointer and nut, threads are good, fuel pump bollts looks stock but seem to be too long   $55

Both for $85 plus shipping

Five cores in various states of disrepair, typical used carbs.  All are the hard to find 1.33 that folks use for FE tripowers.  One has a manual choke.  One is frozen, another carb I had free last year and it re-froze over this winter.  One is missing the throttle shaft and blades.

$160 for all, plus shipping.  Will bring to a swap meet or USPS money order.  $7 extra for Paypal.

Starting to dig into my stash of 62 Galaxie parts. 

NOS COAZ-7526-A windshield wiper arm (also fits up to 64)   $40
NOS C2AB-6204460-A Galaxie 500 glove box emblem   $95   no box, not reproduced
3 used front fender stainless eyebrows, have small dents, much better than average, plus free used 1962 Galaxie license plate frame  $90
4 used hubcaps, bright finish but have shelf wear, one has shallow dents  $65  SOLD
Dash instrument cluster with clock, but missing speedometer  $62

Adding some more parts:

500 gas tank door trim panel and emblem, fair condition  $25
Right side quarter eyebrow above taillight $40
Unknown lower rocker panel trim part about 2 1/2" long $15
Bench seat trim $40
Interior kick panel trim, two red passenger sides $30
Interior kick panel trim, left and right, champagne color $50

64 Galaxie headlight bezel set $150  plus have some individual headlight bezels - but no RH outside ones.

Bostrum seat core with tracks from van - for Thunderbolt or Lightweight clone  $275

64 Fairlane tan kick panels  $45

Trying to keep prices low by not using $bay and only taking USPS MO's.  These are actually parts from a project car, and like 90% of the stuff I'm selling here are not vendor stuff just parts taking up space that I've had a long time.

Some links:

https://pittsburgh.craigslist.org/pts/6000514378.html

https://pittsburgh.craigslist.org/pts/5999595053.html

https://pittsburgh.craigslist.org/pts/6006977498.html

https://pittsburgh.craigslist.org/pts/6007307581.html

https://pittsburgh.craigslist.org/pts/6019862030.html

https://pittsburgh.craigslist.org/pts/6019761954.html

https://pittsburgh.craigslist.org/pts/6014577774.html

https://pittsburgh.craigslist.org/pts/6027903410.html

https://pittsburgh.craigslist.org/pts/6034731626.html

https://pittsburgh.craigslist.org/pts/6041289674.html

Plus there are some other parts on the Pittsburgh craigslist.

Sixteen new old stock valve springs for a 428 CJ.  Blue strip dual springs, 2" free height, 1.25" outside diameter, almost 0.8" inside diameter.  $50 plus $7.50 shipping.

I'm winding down the Oldcrabs website and not putting any new parts on there.

Meanwhile have some NOS point plates to sell, but not taking paypal anymore.

1. Bare point plate with screws and aluminum adapter $45

2. Point plate with screws, USA made condenser and points, and aluminum adapter $60

3. Point plate with screws. USA made condenser and points, aluminum adapter, wiring, advance springs and instructions for installing springs $85

Can ship these; $7 for Priority small flat rate box, its possible to put multiple plates in one box. No Paypal or credit cards.

Have one point plate with screws but no adapter plate for $30.

Note - adding this later:  I have a quantity of five of 1 and 2.  And three of 3.  Free shipping if you buy two or more of any combination.

Some kind of Galaxie big block clutch equalizer bar (I think).  Abused and dirty.  The short leg is bent.  The pivot is loose and the pushrod has been cut and welded.  $50 plus shipping.

Early steel cover with welded on timing pointer  $40 plus shipping

The cover from hell, seriously...666 date code, a mis-cast code on a C3AE-A casting.  No timing pointer  $45 plus shipping

Both are dirty and greasy but in good condition.

Wanted PAW cast aluminum valve covers for a small block Ford.  PAW made some of these pentroof style valve covers before they went under (mostly - still in business, somewhat) back in around 2006-2008.  There were made in two styles with plain fins and with 427 cast between the fins.  Prefer the plain fins version.

Link to picture:

http://forums.vintage-mustang.com/vintage-mustang-forum/609069-fe-styled-valve-covers-sb.html