Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Twinibeam66

Pages: 1 [2] 3 4
16
FE Technical Forum / Re: First 390 build
« on: April 20, 2020, 08:22:55 AM »
Sharp Truck !!!

17
FE Technical Forum / Re: 02 meter
« on: April 13, 2020, 09:52:04 AM »
Thanks Everybody for the replies

18
FE Technical Forum / 02 meter
« on: April 09, 2020, 10:31:43 AM »
Hey everybody was wanting to know if anybody has one of these meters, Does it work good ? Innovate LM-2 Digital Air/Fuel Ratio Meters 3806 ??
Also where should the 02 sensor be mounted ? 

Thanks everybody

19
FE Technical Forum / Re: 482 going on pump. Guess the HP version 2.0, prize to winner.
« on: March 16, 2020, 09:00:55 AM »
639 HP 

20
FE Technical Forum / Re: Time for another guess the horsepower game....
« on: March 11, 2020, 09:41:43 AM »
528 HP !!!

21
FE Technical Forum / Re: Heat spacer or Carb spacer
« on: November 25, 2019, 02:04:37 PM »
Ok Thanks Drew Pojedinec  my breather is a Ford Motorsports im thinking its 12 inches but might be 14. But anyway i will check that really appreciate it.

22
FE Technical Forum / Re: Heat spacer or Carb spacer
« on: November 25, 2019, 10:50:47 AM »
Thanks Drew Pojedinec  thats good to know, thanks for the help everybody

23
FE Technical Forum / Re: Heat spacer or Carb spacer
« on: November 22, 2019, 02:02:37 PM »
Thanks plovett i will remember that i should have plenty of room , going in 66 Truck


24
FE Technical Forum / Re: Heat spacer or Carb spacer
« on: November 22, 2019, 01:27:59 PM »
Dang you did a good job Joe-JDC they look great ! And i have 1 haha, Falcon67  let me know how the 2 inch super sucker does when you get it, like i need to spend some more money ?? Cant buy enough to keep this 390-416 going  haha

Thanks everybody

25
FE Technical Forum / Re: Heat spacer or Carb spacer
« on: November 22, 2019, 09:25:47 AM »
Wow Ctcobra 12 HP thats good i will check that spacer out, also Joe-JDC good article , thanks for the replys. Im thinking i am going to try a 1/2 inch open spacer or one that matches the RPM intake with the 1 inch super sucker on top and start there and see what happens ???    Great forum appreciate all the help everybody

Twinibeam66 

26
FE Technical Forum / Re: Heat spacer or Carb spacer
« on: November 20, 2019, 02:42:19 PM »
Thanks Falcon67 i like the way you put that   haha

27
FE Technical Forum / Re: Guess the horsepower - second of two - "461 truck motor"
« on: November 20, 2019, 01:59:38 PM »
487 HP   

28
FE Technical Forum / Re: Heat spacer or Carb spacer
« on: November 20, 2019, 01:47:14 PM »
Ok thanks for the reply GerryP  i have NO experience with a super sucker so was just wanting to see what had worked for everybody else.

29
FE Technical Forum / Heat spacer or Carb spacer
« on: November 20, 2019, 10:20:19 AM »
Question i have a 416 build with a RPM intake real close to getting it running, i have a 4 hole super sucker are most of you running a open spacer of any kind under it or are you just using a heat gasket on the intake and then the 4 hole ????  What works best ??

Great forum

Thanks Everybody !!

30
FE Technical Forum / Re: Another guess the horsepower to throw in the mix......
« on: November 05, 2019, 08:49:07 AM »
First run 181 HP

Second run 225 HP

Pages: 1 [2] 3 4