46
Private Classifieds / Re: WTB standard bore 428 block
« on: June 11, 2020, 08:49:48 PM »
I've got some Ross, give me a call.
540-664-for four one ate
Jack
540-664-for four one ate
Jack
Dedicated to Building and Racing the Ford FE Engine
News:
SMF - Just Installed!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
47
FE Technical Forum / Re: C5AE-12127-E Dual point Distributer info
« on: May 02, 2020, 08:59:08 PM »
The 6m could MAYBE be used in a 67 GT500 but you'd have to find the right guy restoring an early car.
Depending on condition, I'd say 4-500 IF it's the right date for a Shelby restoration. To everyone else it's just a dual point and it's worth 250 or so.
The 71 is worth about 150
Jack
Depending on condition, I'd say 4-500 IF it's the right date for a Shelby restoration. To everyone else it's just a dual point and it's worth 250 or so.
The 71 is worth about 150
Jack
48
FE Technical Forum / Re: Flexplate application question
« on: April 27, 2020, 08:52:47 PM »
I've got a pile if anyone needs one. On the house.
49
FE Technical Forum / Re: Cam Id help
« on: April 27, 2020, 08:44:00 PM »
Yes, the "E" was the stacked CC for comp cams. It was hard to recognize. I'd post a picture but it's a pain in the ass to do so here...
50
FE Technical Forum / Re: Cam Id help
« on: April 27, 2020, 03:26:49 PM »
Got it sorted, thanks guys.
51
FE Technical Forum / Re: Aftermarket iron block cost options
« on: April 26, 2020, 11:34:32 AM »
We'll have Pond iron blocks in the near future. Things are being delayed for the obvious reasons right now.
Jack
Jack
52
FE Technical Forum / Re: Cam Id help
« on: April 26, 2020, 08:25:07 AM »
Thanks, that might possibly be it, but I've never seen a Comp Cam without CC on it...? I'll call them tomorrow. Much appreciated.
53
FE Technical Forum / Cam Id help
« on: April 25, 2020, 03:42:34 PM »
I bought a Hi Riser engine out of NC recently and I'm trying to get some information on the roller cam that was in it.
Stampings indicate that it was a Holman Moody block at some point, but it was built back in the 90s I believe in its current status.
I can't seem to post a picture here but on the back of the cam is:
Stamped in the back are 2019 A & 5 95
Hand engraved are
312B- R8
E
KA0763
Any help appreciated.
Jack
Stampings indicate that it was a Holman Moody block at some point, but it was built back in the 90s I believe in its current status.
I can't seem to post a picture here but on the back of the cam is:
Stamped in the back are 2019 A & 5 95
Hand engraved are
312B- R8
E
KA0763
Any help appreciated.
Jack
54
Private Classifieds / Re: 57 Ford Not Mine
« on: April 22, 2020, 01:45:45 PM »
That belongs to my buddy Ben Hertel, a member here as well but much more active on the Facebook Ford Forums.
55
Private Classifieds / Re: FE Parts (again not mine) too much time on internet Ft. Worth TX area
« on: April 19, 2020, 09:44:21 PM »
I do, seen the stuff multiple times.
56
Private Classifieds / Re: FE Parts (again not mine) too much time on internet Ft. Worth TX area
« on: April 19, 2020, 10:14:32 AM »
Just a heads up, buyer beware with John's stuff.
57
Private Classifieds / WTB 352/390 HiPo engine or parts
« on: April 01, 2020, 08:49:48 PM »
Looking for the above, let me know what you have.
Thanks,
Jack
540-664-for four one ate
Jacksfordparts gmail
Thanks,
Jack
540-664-for four one ate
Jacksfordparts gmail
58
Private Classifieds / 428 Super Stock Engine - Fresh
« on: March 31, 2020, 01:21:17 PM »
428 CJ S/S Race Engine
Fresh 4.170" bore 8H7 C Scratch 428 block
New JE Pistons
Moldex Billet Crank
Crower Billet Rods
Jim Morgan Ported CJ Heads
Comp Cams Custom Solid Roller Cam and Lifters
Brand New Race T&D Rocker Assemblies
Custom Single Plane Intake
CJ Carb Customized by Davinci carbs and tuned to the engine
Neutral Balanced
ATI Super Damper
New Bearings and Rings
All Top of the line parts, no expense spared
Engine was a back up engine for a competitive team that has not been run since it was freshened up. Stored correctly, rockers backed off.
Engine was run in a S/S Mustang and then GT/C in NHRA. Car ran 10.0 at 3250lbs
Engine is located in VA but shipping is no issue.
Pics available upon request
$11,500
Jack
540-66for-four for one ate
jacksfordparts gmail
Fresh 4.170" bore 8H7 C Scratch 428 block
New JE Pistons
Moldex Billet Crank
Crower Billet Rods
Jim Morgan Ported CJ Heads
Comp Cams Custom Solid Roller Cam and Lifters
Brand New Race T&D Rocker Assemblies
Custom Single Plane Intake
CJ Carb Customized by Davinci carbs and tuned to the engine
Neutral Balanced
ATI Super Damper
New Bearings and Rings
All Top of the line parts, no expense spared
Engine was a back up engine for a competitive team that has not been run since it was freshened up. Stored correctly, rockers backed off.
Engine was run in a S/S Mustang and then GT/C in NHRA. Car ran 10.0 at 3250lbs
Engine is located in VA but shipping is no issue.
Pics available upon request
$11,500
Jack
540-66for-four for one ate
jacksfordparts gmail
59
Private Classifieds / Re: WTB 4 SPECIAL HEAD BOLTS 4 DOVE HD ROCKERS
« on: March 08, 2020, 12:09:56 AM »
Dean, check the buyer beware board on this forum about buying things for Dove these days.
60
Private Classifieds / Re: 1967 427
« on: March 07, 2020, 05:31:35 PM »
Lenny he sold it, and it had low riser heads on it, definitely not an all original engine.