Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mtburger

Pages: 1 2 [3]
31
Private Classifieds / WTB Motorcraft 2100 1.33 390 2V Carb
« on: February 13, 2016, 02:39:32 PM »
Hello All.

Hey, I am in need of an old 390 2v Motorcraft carburetor with the 1.33 venturi that would be a good candidate for rebuilding.

Hope one of you guys have something hanging around somewhere.

Thanks much, Mike H.

32
Private Classifieds / Re: 351c Offenhauser Tunnel Ram With Single and Dual Quad Tops
« on: August 20, 2013, 09:25:50 AM »
Sold!!!

Thanks much, Mike Howard.

33
Private Classifieds / Re: 351c Offenhauser Tunnel Ram With Single and Dual Quad Tops
« on: August 16, 2013, 03:03:28 PM »
Hello Cory.

It might.

My concern is that there is very little support / reinforcement on what is left of the front and rear rails, and the Turkey pan adds two more surfaces to seal.

My immediate thought was that it would be a weeper at the front and back of the block,  but I would need to try it to be sure.

Given my luck at such endeavors in the past, I was not very optimistic.

Thanks, Mike H.

34
Private Classifieds / 351c Offenhauser Tunnel Ram With Single and Dual Quad Tops
« on: August 14, 2013, 10:42:55 PM »
Hello All.

I bought this intake (site un-seen), to use on a 351c project.

So when I got it home and took it out of the box I was kinda bummed out, being that the seller made absolutely no mention that it was all windowed out, and cut up like it is.

That being said, obviously this would make is a great candidate to be used on one of Jay's adapters, as there is just the two small pieces of end rail left to remove.

My only real option to be able to use this, is to fabricate a valley plate, a jig to bolt the intake too, and weld the valley back together in it. At this point I would just like to try to get my money back if possible.

I will take $225, plus the shipping for all 3 pieces.

I attached a bunch of pictures.

Mike H.




















35
Private Classifieds / Re: WTB FE Engine Mounts Mustang / Cougar
« on: May 28, 2013, 12:13:45 PM »
The Torino ones are different, and I am just using these for mock up at the moment, so used would be ok.

Crites sells repros for $150.00 a set, plates and isolators.

I will go that way if nothing used pans out.

Thanks for the replies, email sent to slotracer.

Mike H.

36
Private Classifieds / WTB FE Engine Mounts Mustang / Cougar
« on: May 23, 2013, 01:56:07 PM »
Hello All.

Looking to buy a used set of isolators and block plated to install an FE in a 69 Cougar.

Thanks much, Mike H.

37
Non-FE Discussion Forum / Re: New Members - Introduce Yourselves Here!
« on: December 19, 2012, 05:03:57 PM »
Hello All, Mike Howard here. I am a registered member on several of the Ford forums, and the HAMB. I use the same name on all of them, and I generally do not post much unless I have first hand, on topic info, but I do read a ton.

I have several projects in various states of build or completion, and really enjoy the time I get to spend in my Barn with them and my buddies.

This is my current FE project, and as with the rest of my projects, I take a great deal of pride in doing most all my own work, (although I have had one professionally built Cleveland engine done for me in the past).

It is a 69 Cougar XR7 I bought in 85 and drove as a daily driver for a couple years before breaking it down to make a hot street car out of. That was prior to getting married, which sidelined the project for about 15 years. It is now back on track, and I have collected a nice set of tunnel port heads and  2x4 intake for it, along with a pile of NOS items before they became impossible to find like the complete grill, most all of the chrome, and a NOS quarter panel that I sawed up so the tires would fit.

Thanks for the space, Mike H.





Pages: 1 2 [3]